mini quad 3d models
136005 3d models found related to mini quad.cults3d
This mini quad format 130, chassis in stl and dxf version. ... Video: https://youtu.be/VCqCdpjaP7Q The main chassis is 33% PLA The hull is 20% TPU
thingiverse
Mini quad frame in openscad, a couple of parameters you can set for motor body diameter and prop length to auto adjust spacing. ... To do - create battery plate
thingiverse
Ce mini quad format 130, châssis en version stl et dxf. ... Vidéo : https://youtu.be/VCqCdpjaP7Q Le châssis principal est en PLA en 33% La coque est en TPU en 20%
thingiverse
mini Quad sized like a Hubsan printed in 0.3 u can use Hubsan Motors (8,5mm) i used this one http://www.banggood.com/Chaoli-CL-820-8_5x20mm-Coreless-Motor-for-90mm-150mm-DIY-Micro-FPV-RC-Quadcopter-Frame-p-1054803.html Hubsan FC or a 32 bit FC for...
thingiverse
3D printable mini quad concept. Not tested yet. The landing gear was intended to be printed in a transparent material and the little feet in TPU for some damping. Designed for 12 x 12 mm mount spacing motors with 5030 props or similar. ... - FC...
thingiverse
Mini quad side skirt for sub 200 mm quad, 20mm tall upper and lower battery strap holes.
thingiverse
To hold plastic tubes which houses the antenna on the sides of the mini quad with minimal hardware. ... Instructions .2 layers with 20 percent infills.
thingiverse
My own low-profile take on a mini quad wall mount. ... I printed in M3D Tough 3D Ink Flexible Ruby but any PLA/ABS should work well.
thingiverse
Made these to mount all the boards I want inside of the Spank mini quad frame. I am going to reconfigure them again with a cleaner approach to clean up the wiring and weight. ... For Spank mini frame.
thingiverse
Motor mounts for mini quad motors (8.45mm) to be affixed to a foam glider. edit: I realized the parts were not connected on my .stl file. Sorry about that. ... I fixed it.
cults3d
Motor mounts for mini quad motors (8.45mm) to be affixed to a foam glider. edit: I realized the parts were not connected on my .stl file. Sorry about that. ... I fixed it.
pinshape
Frame for mini quad. For 8mm motors. My equipment is from EX100. Supports needed.I used grid 1% density,65 deg. overhang angle. ... My designs are free and always will be,if u enjoy leave a like to motivate me :)
thingiverse
Remix of the Mini quad, however this is much easier to print and I have included the 280mm arms to accommodate 8x4 props. ...Video:https://www.youtube.com/watch?v=wLS-gQTVVis
thingiverse
It's been designed to fit the FPV250 Mini quad frame 250mm. I made 4 socket for screws, but since the Makerbot cannot print hi-res screws (like the M2.5) I left the holes very small so you can use a M2 or a self drilling screw. ... PRINTING...
thingiverse
Quad frame for mini 130mm quad copter Motor holes are for M2 screws on a 12mm circle Flight controller holes are 30.5mm square (for ~36mm flight controllers) Use 1304 motors with 3" diameter props
thingiverse
Simple display stand for mini quads. Can accommodate quads with Undersung batteries and top-mounted batteries Made up of three parts; Base Stem and Mount. ... The mount is available in 3 sizes Standard Mount Suits 16mm Battery Strap Standard Mount 2...
thingiverse
Here is a mini quad I designed to be printable in a Printrbot Simple Metal. to assemble you will need: 2x layer 1 & layer 3 1x layer 2 4x spacer arms 16x M3x8mm machine screws 4x M3x16mm machine screws 4x M3 hex nut Update: Added a base plate...
thingiverse
Here are some pods/bumpers for the bottom of 8.5mm mini quad motors. ...I made these to hold the LEDs and provide some bounce protection to my motors when I moved my Hubsan X4 h107c electronics onto one of the models included in:...
thingiverse
The mini-quad challenge gate uses a laser diode and a light dependant resistor controlled by an Arduino to detect mini-quads flying through. When a mini-quad is detected it sounds a buzzer and lights up another light in the Neopixel array. See how...
cults3d
After doing a fair amount of experimenting with mini-quads over the past year or so, I have found that the 250 size carbon fiber mini-quads that have become ever popular in the RC community, are just a tad bit too small to comfortably fit all of the...
thingiverse
After doing a fair amount of experimenting with mini-quads over the past year or so, I have found that the 250 size carbon fiber mini-quads that have become ever popular in the RC community, are just a tad bit too small to comfortably fit all of the...
thingiverse
With a friend, we've made a mini quad-copter with clips for assembling. It's not necessary to glu it, just "clik" it. I put HK multistar 1704-1900 on it and a multiwii FC, the mobius and another litle cam for FPV with video transmiter. The weight is...
thingiverse
With the recent wet weather I wanted something to allow me to place my GT-M200 in mud or grass without actually having to place the quad on the ground, I developed this for my GT-M200 but I would imagine it would fit most other true X 5 inch mini...
thingiverse
Please find my new first mini quad 250mm Abs and Anodise Aluminium (stronger than abs only) flight video : https://www.youtube.com/watch?v=dZc_hx9XRNc&feature=youtu.be Weight : 400 grammes (550 with fpv, for this motors very good-:) Designed for CC3D...
thingiverse
H8 Mini quad frame(x1). Includes motor/blade protector(x4), and battery holder(x2). Parts need to be glued. I use loctite super glue for PLA, and loctite plastic bonding system for t-glase. Highly recommend printing in a translucent filament. I...