miniature display case 3d models

I use these dampening feet on my printer: https://www.thingiverse.com/thing:2957365 I embedded 24 hollow areas to fit 6x3mm magnets in the display case and the mount (12 in the display case, 12 in the mount). After assemby i realized, that it will...

This is an Insert that fits inside the base of the Hot Wheels display cases used for some Red Line Club and 100% Hot Wheels cars. When stacked, these cases don't sit flat. The tabs from the top of the case, used to secure it to the base, stick out. ...

So if you bought a Chinese display with three boards from Aliexpress, I highly recommend buying it with a case already included. However, if you can't or don't want to waste a lot of filament, here's my poor man remix of the case. It's a 3-part...

You can use the small switch on the display to change its orientation.Bugs:After making this case, I found an bug in the BTT Pi TFT70 V2.0 design in that if you mount the Raspberry Pi directly to the mount standoffs on the back, its PCB touches...

This case houses a nodemcu v2 'Amica', a 0.96" OLED display and a BME280 sensor. The latter gets slipped into a pocket which is easy to seal off with a little elastic gum so the measurements are a bit less influenced by the controler's warmth. Adding...

I made the case to stand the display up and tilt it back 10 degrees from the vertical for easy viewing and tapered the bezel around the display since the display is a touch screen which you use to select pages and alternate between 12 and 24 hour...

Just a little amount is enoughAssemble the L&R bracket with M4x10mm screws and you're done.Attached are the DSI display I used for this case, yours might be different. If you have a different model or suggestion for better features, please let me...

Just a little amount is enoughAssemble the L&R bracket with M4x10mm screws and you're done.Attached are the DSI display I used for this case, yours might be different. If you have a different model or suggestion for better features, please let me...

Having 2 such display cases on the table looked also not good, because they were moving around and the cables from the one display often were above the display from the other one…Therefore I designed my own case now that can keep 2 HyperPixel 4.0...

If you have a display with hdmi / usb, feel free to remix.The case can be used without the 4040 extrusion mount since it has its own stand in a 45° angle (file: klipperscreen_Fussplatte).If you want to use the 4040 extrusion mount, make sure that you...

Here's a brand new take on that idea - Introducing the "Raspberry Revival" - A sleek and sturdy 7-inch display case for your trusty Raspberry Pi, specifically designed to bring your projects to life with ease. This ingenious device mounts directly...

I have a fork to support this…available here until the PR is merged into the main project:https://github.com/ae5au/pico-solar-systemThanks to Dmytro for the original case design and the Pico Solar System project!Raspberry Pi Pico...

The design allows for holding up to three 28mm scale miniatures in addition to 15 dice and one writing instrument. Three magnet sets consisting of six 5mm diameter x 4mm deep magnets are included. The hinge pin is made from two stainless steel...

Raspberry Pi A+ Showcase Enclosure System Design The innovative Raspberry Pi A+ display case system is specifically engineered to provide an ideal housing solution for the diminutive yet mighty Raspberry Pi A+ single-board computer. This ingenious...

The LEDs on the various modules are visible through the ePaper display, but, if you are using the TPL5111 circuit they will only be lit while the display is updating. Otherwise, a sheet of heavy paper behind the display should be sufficient to...

Parts TTGO ESP32 T-DISPLAY: https://s.click.aliexpress.com/e/_ADirut Battery: https://s.click.aliexpress.com/e/_AonIrT Software options Flight radar: https://github.com/rzeldent/esp32-flightradar24-ttgo Clock:...

DISPLAY CASE/STAND for SHARP 7inch 1920x1200 IGZO LCD kit. Please refer to readme_049rv3.pdf for assembling. -Requirement- Sharp 7inch 1920x1200 IGZO LCD display kits can be purchased from http://akizukidenshi.com/catalog/g/gM-10016/,...

*NOTE: If your battery has a JST 1.25 connector already, check the polarity carefully with the cable included in the TTGO board.* ## Parts * **TTGO ESP32 T-DISPLAY:** https://s.click.aliexpress.com/e/_ADirut * **Battery:**...

This is a case for my 7-inch display that's specifically designed to house the Raspberry Pi 3. I've chosen the SC7B from Amazon seller Kuman, which fits perfectly inside. To secure the RPI in place, you'll need to use the hex standoffs included with...

This is a wall mounting case for a Nextion 3.5" LCD touch display combined with a Wemos D1 Mini (ESP8266) board to control it. The Nextion display gets secured by four small screws - I grabbed some random ones lying around, sorry no specs available.

This case contains an Amica nodemcu v2, a 0.96" OLED display, and a BME280 sensor. The BME280 is inserted into a pocket that can be easily sealed with elastic gum to minimize its impact from the controller's warmth. The rest of the components are...

Case for for 7inch QLED Quantum Dot Display, Capacitive Touch, 1024×600, G+G Toughened Glass Panel https://www.waveshare.com/7hp-capqled.htm Created according to the model:...

Display: https://www.amazon.de/gp/product/B08H23KB1G/ref=ppx_yo_dt_b_asin_title_o01_s00?ie=UTF8&th=1 Important detail: an additional "z_drive_baseplate" must be installed so that the housing does not sit on the base - see it on the photo The...

I'm using this touch screen: https://www.amazon.com/Raspberry-Display-kuman-Interface-SC06/dp/B01CNJVG8K/ref=sr_1_5?dchild=1&keywords=tft+480+320&qid=1620096992&sr=8-5 I also remixed some of the mount parts from this thing:...

Display box for 4xMAX7219 (Multi filamente + Single filament version) You can use PLA, PETG or others but of a light color (recommended white) , since the screen has 0.8mm of plastic in front that is used as a diffuser. MMU version separate the...

This is a 3D printable case for the Raspberry Pi 4 with a 7" touchscreen display, available here: https://www.amazon.com/gp/product/B07L6WT77H/ Front - Printed face down without supports, but if you're experiencing warping at the corners, try...

3d model of a display case with vase. Perfect for games, scenes or renders.|| TEXTURES ||Models includes high textures with maps:DiffuseBumpNormalSpecularDisplacementAll textures are UV mapped for easy editing. || GENERAL ||Easy editable.Uv...

Created Mounts to bring Ender V2 display out of Creality case. During testing, I realised that I had created clips to hold the fabric a bit tighter. (It does sag a little bit). I did the base mount first, used a corner to make the mount more...

Adapter to replace a Makerbase Robin TFT35 V1.0 as found in TwoTrees Sapphire Pro SP3 and other printers with a FySetc, BigTreeTech or Makerbase Mini 12864 Display. Also compatible with the Voron STM32-Mini USB-Adapter (...

Atari game cartridge display cases are being created as part of a research team focused on Human Centered Design & Engineering at the University of Washington: Atari Women (www.atariwomen.org).\r\n\r\nThe design is intended to honor the often-untold...