minolta 16 qt 3d models
91870 3d models found related to minolta 16 qt.thingiverse
film cannister made to fit into the minolta 16 lineup of cameras. this was made from scratch by using photos and measuring a camera's film port. ...it was not tested so if there's a problem let me know.
thingiverse
This is a remix of nikutama05's filament storage box that holds 4 spools of filament with these changes: * Designed for US-based 5/16 threaded rods. You need 2 of these that are each 12 inches long. * Compatible with inexpensive 608 bearings (as...
prusaprinters
There is an improved remix here.This is a remix of nikutama05's (on thingiverse) filament storage box that holds 4 spools of filament with these changes:Designed for US-based 5/16 threaded rods. You need 2 of these that are each 12 inches...
thingiverse
Customized version of https://www.thingiverse.com/thing:2733619 Created with Customizer! ...https://www.thingiverse.com/apps/customizer/run?thing_id=2733619
thingiverse
The QT is a brush wiper sized for a quart size paint can. It snaps onto the pail by pressing the narrow end against the rim and pushing the top surface forward using both thumbs. To remove, lift up on the outside lever. This version differs a bit...
thingiverse
http://www.thingiverse.com/apps/customizer/run?thing_id=714444 Instructions Using the following options: textstring = KONICA MINOLTA fontfilename = write/Letters.dxf baseheight_percent = .33 basethickness_percent = 0.1 shift_font_percent = 0.07...
grabcad
SUPORTE TIPO QT 2525 R PARA TORNEAMENTO DE ROSCA E CANAIS (THREAD AND GROOVE TOOL)
thingiverse
An extract of just the QT Py mount. This will allow you to easily add this mount to other builds without having to re-create it. ...
cults3d
QT also has holes on either side of his body, where a retractable arm comes out, which has a hole in the middle of the palm for vacuuming. QT is very serious and has a lot of pride. The robot is somewhat of a maternal figure to Dandy and Meow...
grabcad
PCB of Adafruit's INA219 High Side DC Current Sensor featuring STEMMA QT connection.Modeling performed in Fusion360 based on the PCB fabrication print found on the product's overview page...
prusaprinters
No supports needed.The light pipe was printed with .05mm detail layer height, 100% infill, with clear PETG.Assembly:Using tweezers and CA glue, install the light pipe into the main body of the bracket so that the end of the light pipe fits through...
thingiverse
http://www.thingiverse.com/apps/customizer/run?thing_id=99020 Instructions Using the following options: sleeve_z_offset = 0 thickness = 2 res = 30 overlap = 3 size = 16 height = 101.6 sleeve_height_percent = 80 bottom_diameter = 88.9 line_thickness =...
thingiverse
MINOLTA REAR LENS CAP A Minolta rear lens cap modelled after the classic original. Designed in Fusion 360. ... Edit: 12.11.2020 I added a version with minolta embossed.
thingiverse
Standard enclosure for Stemma QT form factor sensor from adafruit, 2 versions one with dual QT Ports (input and output) and one with a single QT port
thingiverse
Slight alteration from original Minolta MC/MD to Canon EOS mount by numb_dog on Thingiverse: https://www.thingiverse.com/thing:1495107 Added stops on the md fitting and hole it the ring for the canon stop
thingiverse
This is a little bumper for the viewfinder. ...I don't know if Minolta ever made an official version of this but I tried to keep it in the angular 80's futurism style of the camera.
grabcad
Turbine Flow Meter 31VH-xx-xx.xxxModel Reference : Hydrotechnik QT-500
thingiverse
YouTube Video https://youtu.be/NaFqSdJdPmQ Wipper Snapper Quick Start Guide https://learn.adafruit.com/quickstart-adafruit-io-wippersnapper QT Py Snap Fit Case Learn Guide https://learn.adafruit.com/qt-py-snap-fit-case QTPY ESP32-S2...
cults3d
YouTube Videohttps://youtu.be/NaFqSdJdPmQ Wipper Snapper Quick Start Guidehttps://learn.adafruit.com/quickstart-adafruit-io-wippersnapper QT Py Snap Fit Case Learn Guidehttps://learn.adafruit.com/qt-py-snap-fit-case QTPY...
thingiverse
Since there are no longer camera body caps made for the older Minolta MD cameras, I decided to make my own. Grooves in the cap allow it to interface with the lens-locking mechanism in the camera so you don't need to worry about the body cap...
cults3d
https://youtu.be/d8EX05wC9XY Organize projects with modular Lego base plates for QT Py ! These 3d printed holders feature built-in standoffs for press fitting the PCBs. ... Guide: https://learn.adafruit.com/qt-py-lego
thingiverse
https://youtu.be/d8EX05wC9XY Organize projects with modular Lego base plates for QT Py ! These 3d printed holders feature built-in standoffs for press fitting the PCBs. ... Guide: https://learn.adafruit.com/qt-py-lego
thingiverse
FAQ: http://www.thingiverse.com/shivinteger/about [>>>] Generating Attributions log: [0] Thing Title : Bat Clothespeg [0] Thing URL : http://www.thingiverse.com/thing:30487 [0] Thing Author : Nudel_P [0] Thing Licence : Creative Commons - Attribution...
cults3d
... and even media controls. QT Py RP2040 https://www.adafruit.com/product/4900 Micro Switch https://www.adafruit.com/product/818 Code on GitHub https://github.com/adafruit/Adafruit_Learning_System_Guides/blob/main/Single_Button_Footswitch/code.py