mk13 mod 5 3d models
535840 3d models found related to mk13 mod 5.
prusaprinters
... m5 screw. ...I am using openbuilds low profile screws but any low profile screw should work. Print Settings Printer Brand: LulzBot Printer: TAZ 5 Rafts: No Supports: No Resolution: .25 mm Infill: 20 Filament: Gizmodorks PLA white Category: Other
thingiverse
... is motor pulley mod for D3530 motor. ...Pulley A has 5mm hole added. Pulley B also has 5mm hole and 3 holes for M2.5 x 6mm bolts. ...(11mm round cut should be deeper (4mm) and pulley A is quite tight over pulley B printed with 0.2mm and 100% infill)
thingiverse
A case which will fit a Raspberry PI 4, RPI-RF-MOD and a POE module. The poe module used: https://www.amazon.de/DSLRKIT-Raspberry-HAT-IEEE802-3af-Isolation%EF%BC%8CMEHRWEG/dp/B07JPXR9ZN Only one screw is needed to secure everything in place....
prusaprinters
A case which will fit a Raspberry PI 4, RPI-RF-MOD and a POE module.The poe module used:https://www.amazon.de/DSLRKIT-Raspberry-HAT-IEEE802-3af-Isolation%EF%BC%8CMEHRWEG/dp/B07JPXR9ZNOnly one screw is needed to secure everything in place. ...On top...
thingiverse
... Majesty mod. ...The outer diameter of this holder measures about the same as a standard 0.5-liter soda can, making it compatible with nearly all cup holders on the market. ...This design prints seamlessly without any need for supporting structures.
thingiverse
Zenit mod for pinhole day 2023 working 45.5 mm = 0.3 mm pinhole no thread, apply 3-4 drops of glue to hold in place ( so it will be easier to remove than with thread broken in half ) Buddy called that Penit
thingiverse
This box mod bottom feeder, designed for squonking, features: * A 26650 battery (max length 68 mm effective); * A 6 ml bottle (or an 8.5 ml soft bottle available online in Italy); * A MOSFET; * A 12 mm push button. Three types of drip cap holes are...
prusaprinters
Here is a video that explains it.With this mod, the AC sucks in air from outside to cool it's condenser, instead of blowing out the cool air from inside the room.There are 5 files in total. ...A simple version that is easily FDM printable, a more...
thingiverse
Modded Versions of the following: Hydra Fan Duct: https://www.thingiverse.com/thing:4062242 Ender 5 Linear Rail: https://www.thingiverse.com/thing:3782865 Ender 6 linear rail mod: https://www.thingiverse.com/thing:4757747 This works for both BMG...
cults3d
Modded Versions of the following: Hydra Fan Duct: https://www.thingiverse.com/thing:4062242 Ender 5 Linear Rail: https://www.thingiverse.com/thing:3782865 Ender 6 linear rail mod: https://www.thingiverse.com/thing:4757747 This works for both BMG...
thingiverse
Use 2 m1.7*5 screws to hold a pen or another drawing/writing utensil in place. Clips and tape should help hold the paper in place. I can share my cura settings if you want. I followed some of the instructions from this video...
cults3d
PTSG 140 B2 holder = original holder only offset therefore no 0-45° adjustment (only 90°) PTSG 140 B2 holder 0-45deg = Adjustment goes again 0-45°, but table is about 5 mm higher than original. ... I used the following files on my grinder: PTSG 140 B2...
thingiverse
HSKRC Turtle 149 caddx vista mod. ... use supports for camhold
thingiverse
A simple antenna mod for Jumper T-Pro rc transmitter...
thingiverse
Flying saucer mod for Stern's Godzilla pinball machine. ...
prusaprinters
satsana remixed for Aquila holes with BLtouch mod
cults3d
Squonker mechanical mod for 18650 batteries and reset head v2.
thingiverse
Replacement Panels Available for IJoy Shogun Univ Mod Devices.
thingiverse
Magnetic shifter mod. ...Attached using 4x m3 bolts
thingiverse
A silent yet high airflow mod for the Anycubic Chiron. ...
thingiverse
Human: Update: Added mod that tilts fan 10 deg towards cab front and increases motherboard clearance. Files marked. Disclaimer: This mod is designed specifically for Gigabyte GTX 1070 Windforce 2X OC. Check images to verify similarity with your...