mmu2s 3d models

Fixed it and it finished with no issues (.2mm height, Chris Warkocki's MMU2 Pretty PLA V1.2 profile, my tool-change and ramming settings) - Dark Souls knight with BVOH interface supports (50% scale, .15mm height, Chris Warkocki's MMU2 Pretty PLA V1.2...

This is a remix of two great ideas to improve the spool holders that come with the mmu2(s) https://www.prusaprinters.org/prints/2073-prusa-spool-mmu2-holder-upgrade-bearings https://www.thingiverse.com/thing:3113520 First is a clamp to hold down the...

This thing allows you to stack two LACK tables with enough space between them for the mk3 plus MMU2 (including a horizontal mount; see my other things). The spool holders that come with the MMU2 don't work especially well with this setup (or with any...

I just got my MMU2.0 for my Prusa MK3 and had to give creating a visualizer a shot... ...Turns out making a hamster-wheel isn't as creative as I thought it was :(\r\n\r\nEither way, here's my take on it!\r\n\r\nOh and I published an MMU version of the...

wall tubes 6pcs holder between filament and MMU2 unit Print Settings Printer Brand: Prusa Printer: i3 MK3 Rafts: No Supports: No Resolution: 0.2 Infill: 40% Filament: PETG Category: 3D Printer Accessories

I'm experiencing an issue with my filament rolling over in the MMU2 spool holders, resulting in an overlapped loop when unloading. Upon retraction, the loop rolls onto itself and may snap or form a knot. To prevent this, I've found that introducing...

Replaces the compression plate on the MMU2 with actual PTFE fittings. I required this to switch to 3mm ID tubing, as the stock way was not holding the softer tubes securely. I extended the threaded region to strengthen the part compared to the...

... design prints with no raft or supports required. Postscript: I've been informed that this design may not work with the MMU1 to MMU2 upgrade due to a metal coupling in this area. ... The Fusion360 model is included for easy modification and use.

Both mats are expertly printed using my Prusa Mk3 i3 3D printer, equipped with the versatile MMU2 module. These distinctive designs were crafted with precision and care, utilizing the powerful capabilities of Fusion 360 software. Each coaster...

... is based on Thing 3272446, which you can access at https://www.thingiverse.com/thing:3272446 . It employs the same type of Festos mentioned in that design.\r\n\r\nI also added standoffs to terminate the MMU2 PTFE tubes directly beneath the guides.

This is a Magnet improvement to the MMU2S (R2) Selector PINDA part.The only modification, I made, was to place a 6x1 mm round super magnet under the steel ball and filament path.This magnet will keep the steel ball down when the filament is redrawn.

The Frame Holder component of the MMU2 assembly has been modified to accommodate two light bars. One is installed at the front, while the other is housed within the frame holder itself. Two cutouts have been incorporated for Prusa's ip ties, which...

I wanted a way to keep the PTFE tubes off the MMU2 to be organized and not kink as they passed through the acrylic in my Lack Enclosure.  I designed this originally with .17" diameter, but it was way too tight, so I increased the diameter to .19" and...

... the PTFE organized and cleanly routed. &nbsp;I've printed several prints with it in place and the MMU2 seems to have no trouble.I used M3 screws and nuts and they worked quite well to hold it in place. ...&nbsp;The holes in the acrylic are ½".</p>

I print this Dart-Key-Board as a gift. You can print it with a MMU2 or single mode and glue them together. if the Pfeil parts don't fit you have to sand it a little bit. Use super glue. Print Settings Printer Brand: Prusa Printer: i3 MK3 MMU...

... serving as a buffer or wallet replacement. The basic idea revolves around using this cuff to prevent filament from escaping or tangling when it unwinds on a device like the MMU2(s). ...For visual examples, please refer to the accompanying pictures.

The original Prusa project on Thingiverse (https://www.thingiverse.com/thing:2864118) was found to be too tight for the MMU2, so the corner parts were redesigned to provide more vertical space between two Lack tables. The project also includes parts...

This modification makes maintenance of the filament selector for the MMU2(S) significantly simpler. To detach the selector, one must still remove the screws securing the selector's stepper motor in place, but removing the selector rails from either...

Works with a M10 Male Straight Pneumatic PEFE tubes as guides for my MMU2. UPDATE - Larger Holes for the Screws and Also added a stop so the Tube is restrained. I found the tube would pull though when trying to pull filament out of the MMU</p> <p>In...

I mounted my MMU2 horizontally because I typically place the printer on top of a lack table with spools inside unless I need to print something warp-prone, then I move the printer into an enclosure and put the spools on top for easy access. However,...

I will reprint and upload new photos when that is done. Print instructionsPrint with 0.2mm layerheight 20% infill to ensure that the base is heavy enough. No supports/Raft should be needed. The pipes and Holder will need to be printed separately,...

Both printed on my Prusa Mk3 i3 with MMU2. Designed with Fusion 360. Printed 100% infill. For more beermats, see my group: https://www.thingiverse.com/groups/beermats/things Print instructionsCategory: Signs &amp; Logos Print Settings Printer Brand:...

2019-07-20 - Modified the files I've received my MMU2 kit and discovered that the holders are a bit too long, causing the rubber feet of the spool holder to lift off instead of touching down. It was resting on my holder. I've reduced the lip that...

The Ramones beermat round and square - made in Fusion 360 for my Pruse i3 Mk3 with MMU2. These were printed 95mm x 95mm x 2mm, 100% infill. Use Black .STL for either Round or Square and select appropriate White .STL for your print. For more beermats,...

This is my take on the PFTE tube organizer for the MMU2. I've designed it to be versatile and easy to assemble. To get started, you'll need to print two of each tube separator. This will give you a total of four pieces that are 3mm x 10 mm in size,...

This should only be needed if you've extended the PTFE from the MMU2 to the extruder for some reason (like mounting the MMU2 on something other than the frame of the printer). It is designed for wall mounting.</p> <p>v2 - chamfer added to back edge...

Adjustable for spools 200mm to 300mm in diameter and widths up to 102mm.If you don't have the MMU2 holders you will need four 8x22x7mm bearings (like 608zz) and two 8x120mm rods/pipes.2020-11-25 Replaced the 54mm with 55mm. Added 75mm.2020-06-19...

... Version History: v2.1 - Added "extension" models to lengthen the bank, which should only be needed if you've extended the PTFE from the MMU2 to the extruder for some reason (like mounting the MMU2 on something other than the frame of the printer).

Adjustable for spools 200mm to 300mm in diameter and widths up to 102mm.If you don't have the MMU2 holders you will need four 8x22x7mm bearings (like 608zz) and two 8x120mm rods/pipes.2020-11-25 Replaced the 54mm with 55mm. Added 75mm.2020-06-19...

The first five tubes run into the filament buffer - but the 6th position is for a "short cut" tube that I use if I need to quickly print something and don't want to fuss with unloading and loading a buffer slot. Since I installed vertigo235's "Prusa...