mobile phone holders for the car 3d models
3513967 3d models found related to mobile phone holders for the car.thingiverse
This is a mobile phone holder for the car. It is attached to the front seat headrest. It can be adjusted to fit the specific mobile phone, so that it has a secure fit. The holder can be attached in such a way that all buttons and plugs are still...
thingiverse
A universal mobile phone holder for the car and bike. The fixation of the mobile phone is done with rubber bands. . The fixation on the bike with a rubber band, alternatively with cable ties. With the car-adapter, the phone holder can be fixed to...
thingiverse
This is a simple mobile phone holder for the car. It basically fits into the cars CD player slot. (see photos). The holder is big enough to hold a Samsung Galaxy S7, even if the phone has a cover on it. ...
thingiverse
Mobile phone holder for the car. It is meant for fixing the clamp on the ventilation grille of the car. It is made of two parts that can be put together by a snap connection in the center. This connection can be detached and the holder can be...
thingiverse
Another of my mobile phone holders for the car by using the CD player slot. It holds the Galaxy S7 Edge quite nicely in the vertical position. Made with Tinkercad. P.S. ... I know I said no supports, but it could do with a couple of little ones...
prusaprinters
This is a mobile phone holder for the car, once the lower part of the phone triggers the holder the upper arms grab the phone and hold it in place. It does not have the clips for attaching to the car vent, as all cars are different. It however does...
cults3d
Here are some additional mounting patterns (small and large with different orientations), on venting grid for car phone mount (or any gopro type mounting bracket) :...
thingiverse
Mobile phone holder for the car. It is meant for fixing the clamp on the ventilation grille of the car. It is made of two parts that can be put together by a snap connection in the center. This connection can be detached and the holder can be...
thingiverse
... a Samsung A6. I did not want to buy a new mobile phone holder for the car too so I quickly made an adapter. The base simulates the size of the old smartphone (ca. 145 x 74 x 8,7 mm) and has been provided with small brackets for the new phone. ...
cults3d
car mobile phone holder for cassette, valid for any car with cassette tape and for iphone 8 plus even with case or similar.
thingiverse
... 3 controller metal brace. ... Had a mobile phone holder clamp for the car that failed. so that I took that apart too screw on there. ... m4 screw for the arm and the clamps are put together with m3 screws ran in 100% infill for tight strong fit enjoy!
thingiverse
Mobile phone holder for car whit spring retract system! ( This is a good concept, can be refined and made much more better! ) Smart phone is placed into the hook retract system easy and it stays in place whit own weight of the phone, when its lifted...
cults3d
Mobile phone holder for the bike Rod diameter 23mm Maximum mobile phone size 160 x 77 x10mm 4x M6 screw with nut or similar required 2 options for the lid
thingiverse
Mobile phone holder that clips into the air vent. Designed to fit a Galaxy S8 with case but can be easily adapted to other phones. The clip part has been provided separately to allow a quick low quality print to confirm fit into your vent. Once...
thingiverse
Pocket for a mobile phone. ...A very convenient device in the car.
cults3d
With this gadget it is a joy to travel using the mobile phone as a gps. The measurements are for a 137mm x 68mm x 10mm mobile. ...But they can be changed!
grabcad
I'm not sure about the true dimensions of the spring inside. ...I used one I found in a drawer. Haha :D The approximate dimensions of the spring are shown in the picture.
pinshape
Mobile phone holder for cars that can be mounted in the air vent. Adjustable for different widths of phones (toothed design, from 2.25" to 3.5"). Tested with an iPhone 6s with different depth of cases (up to .5" thick). ...
thingiverse
This is a printable mount for those cell phone holders that go in your car, I thought it would be clever since a lot of those mounts have wireless charging built into them. (I broke the suction cup part of a car phone mount a few months ago, but...
thingiverse
This is a bracket that fits on top a suction cup holder for a car the first model was a bit different at the bottom support, now it's open so it's easier to mount the mobile phone
thingiverse
Brodit mobile phone holders for all brands can be found e.g. at https://www.brodit.com/ Use two 3mm felt gliding panels as shown in the picture to create a neat car key holder (protective case). You should consider attaching the mounting plate with...
thingiverse
Additionally i was bothered, that any holder fits to the bare phone, but i don´t want to take of the cases just to fix it in the car. this is designed for a Mi A2 lite incl case, and a Samsung S9plus incl case. It is intended to attach to a...
thingiverse
I originally printed this (https://www.thingiverse.com/thing:3488440) but found it to be unsatisfactory but with potential. ...So, I found a deeper holder and added a much stronger rear support which should fit most mobile phone holders.
thingiverse
... become overheated when navigation to your holiday destination. ...This cap can easily be placed over the phone holder and keeps the direct sun of the phone. This way the phone is less heated. ... Make sure to print in ABS as PLA will deform in the sun.
thingiverse
This model includes the phone holder part and not the part that is fixed to the car - changes based on car settings. Size fits any smart-phone (Since it is auto-adjusting), I use it with LG G4. My original plan, easy to print without any supports and...
thingiverse
Base for a phone holder for the car vents. The ball was originally 17,0 mm, but I made it 17,5 mm to make it tighter. The threads are 5 mm. It is a tight fit when installing the charger, so making the stem 2 mm longer to raise the ball and increase...
thingiverse
Fits your wireless Mac keyboard snugly to hold any smartphone including the iPhone 6+ and any Android phone. Even works for iPad minis! Print Settings Printer Brand: MakerBot Printer: MakerBot Replicator 2 Rafts: Doesn't Matter Supports: Yes Custom...
prusaprinters
Vintage Car phone holder 3.5 x 2.875 x 1 This would be a good Resin print This will also print on FFF. Print Settings Printer Brand: Creality Printer: Ender 3Rafts: No Supports: NoResolution: 100 Infill: 10% Category: Mobile Phone