mobilinkd case for aprs tnc bluetooth modem 3d models

A custom case is designed for safeguarding the impressive Mobilinkd TNC device, which can be found at http://www.mobilinkd.com.

It bears an uncanny resemblance to the TNC1 case, with the only noticeable variation being the absence of the side opening previously required for the slide switch. This omission is largely due to the TNC2's abandonment of a slide switch in favor of...

This is a case for a converted CM108 TNC. The CM108 is a very common, cheap USB audio chip with a few GPIO which make it ideal for creating a TNC:...

The case holds the TNC and has a path for the radio's belt clip to attach. This is one of the first things I've designed myself so it took a few tried to get the tolerances right, but the TNC should fit snug enough that it doesn't fall out. If you...

Case for DS-TNC modem. ...For details on the DS-TNC modem, visit http://sp9uob.verox.pl/dstncv2.html.

Case for dsTNC Modem. ...For more details on the dsTNC Modem, check out http://sp9uob.verox.pl/dstncv2.html in English.

This is a case for the Mobilinkd TNC1. There are two power buttons. Once sits flush with the top of the case. The other is slightly recessed in the case, making it harder to accidentally turn on the TNC. The case is designed to be held together...

Case for dsTNC modem. For information about dsTNC modem see http://sp9uob.verox.pl/dstncv2.html (in polish). Print Settings Printer Brand: Prusa Printer: i3 MK2S Rafts: No Supports: Yes Infill: 15% Category: Electronics

This is a case for the mobilinkd tnc4. It will probably fit earlier versions too. Print 0.15mm or 0.20mm on a reasonable quality setting. Ports left exposed, friction fit. This is mostly designed to protect the power button from being accidentally...

This is a case in three parts: top, bottom, and push-button, designed specifically for the Mobilinkd TNC2.1 with its micro USB port. It shares similarities with the standard TNC2 cases but features distinct differences, including a mini-USB to...

A 3D printable case for the NucleoTNC by WX9O / Mobilinkd. Assemble the parts with M2.5x6 screws. Back panel v2 has tabs that will help with preventing flex on the back side of the case body when assembled. 73! ...de Steve KC1AWV

Retro computer enthusiasts take note: a 3D printed case is now available for the FreeFi-232, a game-changing serial to wifi dongle courtesy of Daniel Jameson's ingenuity. ...To get building, visit this GitHub link:...

This is the wall mount holder for the Meshtastic Lora APRS Case for Lilygo T-Beam, M5 CardKB and Oled 2.4"You just need 2x 3mm screwsYou can find the Meshtastic Lora APRS Case for T-Beam, M5 CardKB and Oled 2.4"...

Secure Fastener Device for High-Speed Connectivity Enclosures The Secure Fastening Mechanism secures external communication system components to their housing or rack enclosure ensuring maximum reliability and minimizing risk of device malfunction.

To hold the SparkFun Bluetooth Mate Silver modem for RepRap Prusa Mendel, I edited an OpenSCAD file for Arduino module, adjusting it to fit the modem and removing extra tabs. The length was set at 40mm with room for solder points. This mount also...

I was after a mount to cradle the SparkFun Bluetooth Mate Silver modem, which I'll be using with my RepRap Prusa Mendel thanks to this link: http://www.thingiverse.com/thing:13506. I modified the OpenSCAD file for the Arduino module to fit the modem...

WVCARC Case for TNC standalone version i did not design this only sharing it here so other people can make it Link to resource https://www.wvcarc.com/p/tnc-96k-resources.html

... a TNC for my Baofeng. ... Check out http://na7q.com/baofeng-tnc/ I felt like it should have a case to better protect it. Just slip the TNC into the sleeve then super glue the lid over the USB end. ...Only a light amount of glue should be used.

... TNC-Pi 9k from WVARC. ...I put it on the Raspberry Pi and wanted a case for the Pi 4 and the TNC-Pi 9k. https://www.wvcarc.com/2018/03/tnc-pi-9k-kits.html I use 4x 2.5mmx35mm Screws to keep it together. ...https://www.amazon.com/gp/product/B0789W9RNJ

This is a case to use with this bluetooth module. I use it to convert old sound systems to bluetooth music. It has holes to embed magnets and a little cap to hide them and attach it to almost any metallic surface of a sound system. Esta es una...

This is a prime opportunity for installing a high-speed cable modem directly beneath a Samsung television in our corporate meeting space.

This is a DIY Wifi Modem project for the Commodore 64 that requires some technical know-how, specifically soldering your own custom PCB to fit inside the housing. I successfully implemented this using the Wemos D1 mini (ESP8266) board, but feel free...

This is an organizer/divider for an Apache 2800 waterproof case to mount a Kenwood TM-281 radio with space for the components for a portable APRS repeater I built.

Case for AWEI Bluetooth headphones.

Case for Mini Bluetooth Amp 92 x 35 x 35 mm

For the Meshtastic Lora APRS Case for Lilygo T-Beam, M5 CardKB and Oled 2.4" i made another backplane where you can mount a Heltec Lora32 V3.The Heltec Lora32 V3 you can get from here:https://heltec.org/project/wifi-lora-32-v3/I took the power direct...

Case for TPA3118 with Bluetooth from [ali](https://aliexpress.ru/item/32683135776.html) with cooling no rafts no supports small 3mm screw for cap and bolts 3mm for plate

Case for Bluetooth HC-06 module. The modular connector used is a type 6P4C with pins to PCB soldering. Circuit schematics can be found at FreeSensors. The case consists of two parts, one upper and the other lower, which must be glued together...

Basic example for an affordable standard Bluetooth Audio module enabling direct connectivity of any headphones using Bluetooth technology or playback of MP3 files stored on a memory card.

Actually I made a case for my Lora APRS with keyboard and bigger display. I used the Lilygo T-Beam with a 2.4" I2C OLED, the M5stack cardkb and a 18650 Li-Ion.You have to decide if you flash the Meshtastic Firmware: https://meshtastic.org/downloads/...