model 3 frunk
2305435 3d models found related to model 3 frunk.thingiverse
ENG:The Tesla Model 3 frunk has two parts (1131205-00-C) that are poorly designed and break easily when you remove the panels on the frunk area and place them back. I designed a part that holds inside the defective part and should avoid breaking the...
prusaprinters
This is an insert to level the floor of the Tesla Model 3 frunk so it can be used for pizza/carry out without the toppings sliding to one side. Print instructionsPETG or ABS recommended to better handle outdoor temperatures unless you live somewhere...
thingiverse
Simple cover to create a deeper recessed hole for the Tesla Model 3's frunk release button. This should help prevent it from being triggered inadvertently by stuff shifting around in the frunk. ... The shroud surrounding the frunk latch pops off very...
thingiverse
If you have a MY2020 Tesla Model 3 then you will know that they do not come with the frunk shopping bag hooks. Now you can print your own. The pieces can be printed without support but I think the results are better if you print with support -...
thingiverse
**In Progress** The new 2020 Tesla Model 3's do not come with the frunk hooks (grocery hooks) anymore. An awesome contributor in reddit (redditor_8675309) scanned these hooks so that anyone that doesn't have them can 3D print them. Feel free to remix...
thingiverse
More recent Model 3's doesn't come with the frunk pair of hooks anymore. Designed these to attach to where the original should be. Just need a 10mm wrench to remove the existing bolt. Insert properly with bold washes space facing up and hook...
thingiverse
This part reinforces or repairs the Tesla Model 3 front trunk (Frunk) supports at the rear edge of the frunk which are prone to breaking when the cabin air intake grille is installed. The Tesla part being reinforced or repaired is 1131205-00-C. By...
thingiverse
Logo MODEL 3 to stick on the FRUNK Double-sided tape transparent to stick on the frunk size : 93.47mm x 11.72mm x 15 mm
grabcad
To avoid smaller items rolling around in my Tesla Model 3 (2021) frunk, I was interested in a secure post or two that I could attach items to. The Model 3 has two adjacent bolt wells in the frunk that can double as securing points.NOTE:Earlier Tesla...
thingiverse
To avoid smaller items rolling around in my Tesla Model 3 (2021) frunk, I was interested in a secure post or two that I could attach items to. The Model 3 has two adjacent bolt wells in the frunk that can double as securing points. NOTE: Earlier...
thingiverse
I prefer to use screws over printed pins and like to avoid supports when possible, so I remixed these frunk hooks to use M3 screws. It's a little klugey - not sure if the original STLs were screwy or if it's because I imported the STLs into...
prusaprinters
Add grocery hooks to your Model 3 frunk!Requires a Tesla Model 3 built on or after August 2020. Supported frunks will have two holes on the inside of the frunk weather stripping, each containing a single bolt.See pictures for correct installation and...
thingiverse
# Tesla Model 3 Frunk Grocery Hooks ## Requires a Model 3 delivered after July/August 2020 with the new frunk design (textured bottom, not smooth) I loved that the frunk used to have grocery hooks, and when they took them out and then updated the...
thingiverse
If the secondary catch on your Tesla Model 3 fails to release this tool helps you open the Frunk
thingiverse
Print at 100%, no support Required: 2x M3x25 hex bolt (20mm is fine too) You can support my work by purchasing the complete model from: https://cults3d.com/en/3d-model/gadget/frunk-hooks-for-tesla-model-3-my2021
thingiverse
This is a tool to help position your Tesla model3's front hood emblem perfectly, simple as that. ... tip would be appreciated :) happy printing
thingiverse
Note the location of the tow hook storage in the image if you aren't sure.[/update] This is an insert to level the floor of the Tesla Model 3 frunk so it can be used for pizza/carry out without spillage or toppings sliding to one side. I was told...
thingiverse
Replacement clips for a Tesla Model S that hold the frunk liner in place to the quarter panel. These are held on from the factory by adhesive strips that wear over time. Mine were practically falling off and got lost. I printed 3 as replacements and...
cults3d
A lid / cover for a 2013 Tesla Model S frunk fuse box. It is redesigned from the OEM version to let you to tap into the fuses to power other mods. I made this as part of my radar retrofit (https://www.thingiverse.com/thing:3667845) The lid is...
thingiverse
A lid / cover for a 2013 Tesla Model S frunk fuse box. It is redesigned from the OEM version to let you to tap into the fuses to power other mods. I made this as part of my [radar retrofit](https://www.thingiverse.com/thing:3667845) The lid is...
thingiverse
Lightweight 2x 40x10mm fan mod for Valve Index frunk. ... 2x 40x10mm 5v fans 8 x m3 skrews and nuts USB plug
thingiverse
In the engine compartment is so much space for Frunks. Here is the first. You need 2 Spacer, 2 Screws, one M5 screw and one frunk plate. ... The Box with lid you can find here https://www.thingiverse.com/thing:6122755
thingiverse
Have rejigged the model for the Kona frunk ( possibly fit a Kia Niro too - will confirm ) to use 3mm or thicker aluminium bars to support the container which is a 30 litre plastic crate from Bunnings, Australia although any container that fits can be...
thingiverse
This is the retaining clip used to hold the Frunk prop rod in place. Follows a similar design to the OEM clip. You can reuse the screw to hold it in place. ... Was designed by M3K.
thingiverse
first of all the original frunk was made by bperraud and can be found here: https://www.thingiverse.com/thing:3732284 Yes i know normally i can add it to the sources but i cant get it to work I liked this Frunk but it was missing some things i wanted...
thingiverse
All materials can be bought at Bauhaus https://www.bauhaus.dk/surplus-systems-eurokasse-euronormbox-600x400x120-mm https://www.bauhaus.dk/surplus-systems-lag-m-haengsler-euronormbox-600x400x10-mm Note: You need to print 2 x part_1 *EDIT: I've added...
cults3d
All materials can be bought at Bauhaushttps://www.bauhaus.dk/surplus-systems-eurokasse-euronormbox-600x400x120-mmhttps://www.bauhaus.dk/surplus-systems-lag-m-haengsler-euronormbox-600x400x10-mm Note: You need to print 2 x part_1 *EDIT: I've added a...
thingiverse
Halterung für Kona electric Modell 2021 (und 2020): ich habe die Befestigungen für einen Frunkhalter überarbeitet. Die kurzen sind etwas passender gestaltet. Bei den Originalen von https://www.thingiverse.com/thing:4065215 saßen die Gummiaufnahmen zu...
cults3d
They are supports to create an economical homemade frunk just print buy the box and place it is recommended that the supports are placed inside the base of the box completely.