mods for ender 3 v2 3d models

My version is slightly chunkier with a thicker bracket that easily accommodates a Raspberry Pi camera V2.1 without the need for any support or rafts. This project requires just two M3 x 15mm hex bolts to assemble everything properly. To print the...

Another remix of this fantastic motherboard cover.Remixed to fit 60x25mm fan and modified/enlarged air vents and walls as well.Included is modified leg to make everything fit. (https://www.thingiverse.com/thing:4603075)Print SettingsPrinter...

Noctua fans I used for the MB and PSU: Noctua NF-A8 FLX (80mm) There's also a mount built in to fit a LM2596 buck converter (43mm x 21mm) I printed both parts (MB and PSU cover) in PLA. PS: If you prefer to add a fan cover - here you go:...

And you will have to raise your printer, I use these feet for that https://www.thingiverse.com/thing:4789307 To get a nice mesh looking you need to set some Cura settings: - Top layers: 0 - Bottom layers: 0 - Infill: Triangles To make this thing...

... in the way otr just didn't work well. This seems to be perfect for my needs and hopefully yours too. Print the mount with supports and the front of the case. I believe this works for the v 1.2 and v2 cameras. ...but I have only tested on the v1.2

... in the way otr just didn't work well. This seems to be perfect for my needs and hopefully yours too. Print the mount with supports and the front of the case. I believe this works for the v 1.2 and v2 cameras. ...but I have only tested on the v1.2

Camera mount for Ender 3 Pro 3D printer. It mounts to the Y Axis extrusion and works great for timelapses.Above timelapse was taken with this camera mount and an adapter to raise the camera a little higher for this print.Uses ¼-20 X 1" bolt in the...

A Raspberry Pi 4 upgrade that adds a sleek, modern design to your existing model B+ or A+, complete with an impressive top section adorned with the iconic Raspberry Pi logo and a sturdy bottom portion featuring the V2 design.

I really liked this fan shroud because it held the 5015 part cooling fan and also the 4020 i have and wanted to be able to mount the orbiter V2 direct drive. My design is really crude but does what i need it to. i didnt pay much attention to the...

(not test fittet yet) The STP is included for adjustment or remixing if needed or desired)in this version the M3 bolts should just go through all the holes without the threads gripping the filament, which should make mounting it a lot nicer, since it...

Update (3/24/21): Added clearance for wheel bolt Update (3/18/21): Fixed slot clearance on wire guide As title says, I took a few models and glued em together using tinkercad. This uses the stock fans. ...this will NOT work if you have an all metal...

Side Tray for Ender 3 V2 Side tray for Ender 3 V2

https://www.amazon.com/Quntis-Computer-Reading-Auto-Dimming-Adjustment/dp/B08DKQ3JG1/ref=sr_1_1?crid=15W0UBN81UWYW&keywords=qunti&qid=1661056119&sprefix=qunti%2Caps%2C176&sr=8-1 This is designed to fit in between the Two screws at the top of the...

I would imagine this works with other Ender 3s but I cannot confirm Note: Originally, I designed this to have studs that the board slides over, but those proved unusable because the ports needs to slide into the holes on the side of the case. So, I...

it is a support to connect in direct-drive an extruder OMG V2 to a hotend PHAETUS Dragonfly BMS. The length of the PTFE tube should be between 50 and 53 mm. ... The PTFE tube should be put into the extruder first and clamped and then inserted into the...

Do this mod at your own risk. ...:)</p><ol><li>(Optional but recommended) Carefully push the fan blades from both sides to remove the fan blade rotor from the casing.&nbsp;</li><li>Cut all the blades</li><li>Sand a little bit to smooth the leftover...

... flipping it backwards. * Some material removed to prevent heater and thermistor wires pinching. * A new mounting hole added to match Ender3 V2 mount plate (one more m3 nut is needed as the hole is not just moved, but no longer has thread as well).

... it in, thats it! You can print either standing up (will require greater time as supports will be larger) or lying down on the side (will still require supports but will be smaller) and lesser time. For Strength can use 3-4 walls and 30% infill.

I swapped the cover from the Sainsmart 5MP camera to the more advanced Raspberry Pi Camera v2.1 with an impressive 8MB. 2. To ensure a secure and tight joint, I reduced the size of the arm from 100% to 98%. If you require an even tighter fit,...

ender 3 v2 ldc cover

The motor mount on the Z axis for Ender 3 / 3 Pro / 3 V2.

The feeder extruder motor mount on the Z axis for Ender 3 / 3 Pro / 3 V2

The limiter endstop stopper for Ender 3 / 3 Pro / 3 V2 - MinimaL Style

(I'm going to try to make another on that can hang on the side of the extruder shroud...)The clip that goes over the back of the extruder head covers over the screw in the back.Instructions for use:You'll need to raise your Z to about 50mm Attach the...

(крепление мотора + крышка "лоМачо") - винт M3x16 - 3 шт. (крышка базы + крышка "лоМачо") - винт M3x18 - 2 шт. (для 4010) опционально - винт M3x20 - 1 шт. (для 5015) - винт M3x30 - 2 шт. ...(для 4020) опционально - пару стяжек для крепления проводки...

A plier holder for IKEA SKADIS

For locking the z-axis screw for things such as mounting a laser.

It is for Ender 3 printers with the upgraded X-axis with the aluminum backplate, which mounts on the two M3 screw holes on the left side. I have a cut-out to fit the Fang cooler around. The dial indicator is specifically the digital one by...

This is an altered version of:- "Ender-3_filament_guide_v2.2". By Flint Weiss. FlintWeiss • Seattle, WA I found that when I screwed it down. The brass bearing from the screw interfered with the fitting. And so I added spacers underneath, to...

... 2) Wired the Fan to the buck converter. 3) Pre-wire you buck converter 4) Clip the buck converter in place 5) Screw the Fan with the supplied screws 6) Be sure your printer is turned OFF and wired the buck converter to mainboard supply. ...