monoprice duplicator i3 3d models
65282 3d models found related to monoprice duplicator i3.grabcad
This camera mount can be easily moved from the front to the back of the Wanhoa, PowerSpec, or Monoprice Duplicator i3. It can also be adjusted on the fly due to the magnetic mounting scheme. The magnets are 12mm by 3mm, found on Amazon and glued into...
thingiverse
This camera mount can be easily moved from the front to the back of the Wanhoa, PowerSpec, or Monoprice Duplicator i3. It can also be adjusted on the fly due to the magnetic mounting scheme. The magnets are 12mm by 3mm, found on Amazon and glued into...
thingiverse
Tool to assist in tramming the bed on a Duplicator i3. ...Included gcode file is for a PowerSpec I3.
grabcad
Tool to assist in tramming the bed on a Duplicator i3.
thingiverse
This dial indicator snap-mounts to the crossbars of a Duplicator i3 - good for quickly and accurately tramming the print bed. Attached to the indicator using 1/4-20 or 6mm hardware. ... Dial Indicator can be found here : ...
grabcad
This dial indicator snap-mounts to the crossbars of a Duplicator i3 - good for quickly and accurately tramming the print bed. Attached to the indicator using 1/4-20 or 6mm hardware. ... Dial Indicator can be found here...
grabcad
Rework of the magnetic camera mount I posted a few days ago. This one is quite a bit more rigid and not as prone to vibrate and it is a single part. The dowside is that this one takes a lot longer to print. ...Six 12mmx3mm round magnets are glued in...
thingiverse
This upgrade is designed to keep the filament organized in the print area. The filament is guided through a tube so it does not roll back to the barrel as the extruder moves closer towards it. Additionally no short sample will curl around the print...
thingiverse
#Summary: I printed most of the parts with supports to keep the surfaces off the bed. The cooler will need to be printed in something with High heat deflection. The mounting point is close to the heater block and will lose shape if the cooler is...
thingiverse
A replacement x-axis cable drag chain (wire carrier) starter link for the Monoprice Maker Select 3D Printer (re-branded Wanhao Duplicator i3). The standard link attaches in a position that creates an undesirable angle and slight vertical stress in...
thingiverse
Replacement spool holder bracket for Monoprice Maker Select/Wanhao Duplicator i3. Use to replace existing bracket, or to add bracket to the left of the original to use a length of PVC pipe as a spool holder. The original spool holder is to short to...
thingiverse
This is a pen holder for a Wanhao i3 duplicator (plus) or Monoprice Maker Select (V2/V2.1/plus). The two holes are meant to fit onto the layer cooling fan mount on the X carriage using M3 bolts and nuts. I used 2 12mm M3 bolts and nuts to secure...
thingiverse
Print Settings Printer: Monoprice Maker Select/Wanhao Duplicator i3 Rafts: No Supports: No Resolution: 0.2mm Infill: 30% Notes: For the Bottom_Braces.stl multiply by 3 and mirror 2 of them on Z. For the Z_Brace.stl multiply by 1 and mirror 1 of them...
thingiverse
I have the Wanhao Duplicator i3 v2.1 (same as the Monoprice Maker Select) and I use glue sticks on top of my glass bed. I normally buy them from Amazon and keep them in the box. I decided that I should use the extra space on top of the control...
prusaprinters
measurements can be found in the Instructable link. Print instructionsCategory: 3D Printing Print Settings Printer: Monoprice Maker Select/Wanhao Duplicator i3 Rafts: No Supports: No Resolution: 0.2mm Infill: 30% Notes: For the Bottom_Braces.stl...
thingiverse
update 1/27/17: came across http://www.thingiverse.com/thing:193948 which is a clever and more clean solution Print Settings Printer: Monoprice V2 Rafts: No Supports: No Resolution: 0.15 mm Infill: 100% How I Designed This edited RotoScan's stl files...
thingiverse
Basic Filament Guide / Oiler for the Monoprice Maker Select and the Wanhao Duplicator I3. ... Designed in Fusion 360.
thingiverse
Filament guide for a duplicator i3. The filament is supported in all directions; the guide can be fitted/removed without unloading the filament. ... photos are printed in PETG at 235degrees, with 90degree bed.
thingiverse
After printing Berky93's Tool holder for my Monoprice Select Plus I decided to model my own tool holder for the other side which compliments his perfectly. It holds the rest of the tools that I use for my printer commonly. This holds the nozzle...
thingiverse
MonoPrice Maker Select V2 aka Wanhao Duplicator i3 V2 printers have an issue where a cable can get hooked on the back of the frame. This print snaps onto the frame and forces the cable up, so it can't catch on the side of the frame. If you...
thingiverse
This was designed to be similar to the FLSUN i3 wobble decouplers, yet for the Wanhao Duplicator i3/ i3 plus, 2.1- Monoprice Maker Select, Maker Select Plus, and other clones of those printers. Original idea: ...
thingiverse
... so I designed a mount for them. Primarily designed to work with this extruder mount or this mount and these bearing blocks. Print Settings Printer: Monoprice Maker Select/Wanhao Duplicator i3 Rafts: No Supports: No Resolution: 0.2mm Infill: 50%
thingiverse
Ready to stop listening to your Wanhao Duplicator i3 / Monoprice Maker Select Plus printer drone on all day? Me too! This little bracket allows you to fit a BigTreeTech SKR Mini E3 mainboard with TMC 2209 silent stepper drivers. If you have any...
cults3d
Ready to stop listening to your Wanhao Duplicator i3 / Monoprice Maker Select Plus printer drone on all day? Me too! This little bracket allows you to fit a BigTreeTech SKR Mini E3 mainboard with TMC 2209 silent stepper drivers. If you have any...
thingiverse
I slightly redesigned the bulkhead for http://www.thingiverse.com/thing:559623 by threading it all the way to the collar so that it can be tightened against a Monoprice Maker Select 3D (Wanhao Duplicator i3) spool holder. With this new bulkhead, it...
thingiverse
This is a thumbwheel for use with the wingnuts on the Monoprice Maker Select / Wanhao Duplicator I3. The numbers do not give absolute position but help you remember which way to turn to raise or lower the print bed when leveling it. The tick marks...
thingiverse
This is designed for the Monoprice Maker Select, but should work for the Wanhao Duplicator i3. Mount these on the bottom of the x-axis rod carriage, as shown in the photos. You'll need a little glue. I used some printed rulers to give an...
thingiverse
... PETG with zero issues. Required: 1x Pulley Bracket 1x Pulley 1x M4x20-35mm screw Existing M5 mount screws Enjoy! Print Settings Printer Brand: Wanhao Printer: Wanhao Duplicator i3 V2 Rafts: No Supports: No Resolution: .2mm Infill: 50% tetrahedral
thingiverse
(This will only work with the offset link.) This is only recommended if you've already installed this excellent drag link for the other end of the chain: https://www.thingiverse.com/thing:1432064 This may also work on the Wanhao Duplicator i3, since...
thingiverse
Print Settings Printer: Wanhao Duplicator i3 Monoprice Maker Select Wanhao Duplicator i3 Wanhao Duplicator i3 V1 Wanhao Duplicator i3 V2 Wanhao Duplicator i3 V2.1 Monoprice Maker Select IIIP 3D Printer Balco 3D Printer Cocoon Create 3D Printer...