monoprice maker select fan 3d models

I'm looking to optimize airflow by experimenting with RevA's print settings, transitioning from RevB. ...Monoprice's standard fan setup is grossly insufficient for my needs, and I'm skeptical that the results will meet my expectations.

I chose to relocate the spool holder on my Monoprice Maker Select to the control box, but I wasn't satisfied with the filament routing into the extruder - it kept snagging on my Z braces or rubbing against the top of the frame. Therefore, this little...

This is a sleek SD card holder that securely attaches to your Monoprice Maker Select atop the control unit. Simply utilize the stock screws designated for the spool holder to screw it in, making installation remarkably effortless. This ingenious...

I managed to break the micro-usb socket on my Monoprice Maker Select Mini printer while moving it. Then, I decided to try replacing the socket with a standard panel-mount 'B' socket (the square one), as that would be more durable in the long run. To...

This design works for the Monoprice Maker Select, but it should also work for the Wanhao Duplicator i3. Mount these on the bottom of the x-axis rod carriage, as shown in the photos. You'll need a little glue to hold them in place. I used some...

I designed this drag chain link because the x-axis drag chain on my Monoprice Maker Select V2.1 was dragging across the top of the little arm holding the limit switch. This is annoying and causes issues. To solve this problem, I raised the drag chain...

I'm excited to share a simple adapter I created to allow standard webcams with a tripod mount to be used with Xenz' "Webcam mount for Wanhao Di3 / Monoprice Maker Select v2.1." To make this adapter, I converted the Webcam Mount and Kahuna's "Tripod...

**Print Settings** * Printer: Monoprice Maker Select v2.1 * Rafts: No * Supports: Yes * Infill: 20% * Notes: + Frame mount: Easy to print, no special instructions required. + Heated bed mount: Requires printing upside down with heavy use of...

I created a cute little Amish Windmill to visually illustrate the extruder's activity for Monoprice Maker Pro (Wanhao D9) Printers, as I couldn't find many indicators available, so now you can see what your extruder is up to in an entertaining way.

Print Settings: Printer: Monoprice Maker Select v2.1 Supports: Doesn't Matter Infill: 20% Notes: All of those long pieces print vertically upwards, so no support is needed. However, do pay attention to Right_Top.stl and Left_Top.stl since you may...

The front feet were remixed using the back feet from AzzA's well known design at this URL: https://www.thingiverse.com/thing:921948 Additional Information: This is a rear mounted z-brace for the Monoprice Maker Select V1 and V2, Wanhao Duplicator...

It also uses the mounting tabs from https://www.thingiverse.com/thing:1686028 by mmoore0.Before I got a Prusa printer, I had a Monoprice Maker Select V2 (RAMPS). I really liked parhamdb's original mPSU mounting model because it offered direct chassis...

I have a Monoprice Maker Select V2 (RAMPS) printer, and I really liked parhamdb's original design because it offered direct chassis mounting, rear plug mount, plenty of space for wiring, and was also visually appealing. Unfortunately, my Sompom...

This modification was designed for the Monoprice Maker Select V2, which should also work with any of the Wanhao Variants. An additional file has been added for those with a 40mm width motor; the original file is intended for the 34mm width motor -...

Original Right side here: https://www.thingiverse.com/thing:1718783 Print Settings Printer Brand: Monoprice Printer: Maker SelectRafts: Doesn't Matter Supports: NoResolution: .2 Infill: 50 Filament: Hatchbox PLA White Notes: A roll of tape...

This clip is designed to fit neatly on the frame of the Monoprice Maker Select Plus (Wanhao i3) above the Z limit switch, allowing for easy adjustments to the home level of Z. These are particularly useful when you've added upgrades that increase...

Print Settings Printer: Monoprice Maker Select V2 Rafts: No Supports: No Infill: 15% Post-Printing Installation Unscrew and remove the filament spool holder on top of your printer. Run the screws through the new guide's holes, then place it below...

But they use it for the part cooling and the fan duct is totally a joke that blows below the nozzle and to the SIDE? for some reason. Anyway I made many versions until I found one that made a great result. This is a great result! It sits a little off...

The Monoprice or Wanhao D9 prints poorly, with the fan being a major concern. It uses a standard 24v side fan designed for cooling hotends but instead employs it for part cooling. The fan duct is woefully inadequate, directing airflow under the...

__Note__: This bed mount attaches directly to the Y-axis plate on your Maker Select v2.1 printer instead of the heated bed, utilizing the square cutout hole provided. To secure it in place, insert the mount into the square hole and latch onto the...

I upgraded the Melzi board to ramps and installed a MOSFET mount inside my Maker Select V2 case. ...Check out the process in this video: https://youtu.be/cpfPAF9jbw0

This is an authentic replacement knob specifically designed to fit perfectly on the Monoprice Select Mini.

... For Mk2, the "snap-in" feature was removed :). Tinker for yourself: https://tinkercad.com/things/2eSYmyBEkIQ Print Settings Printer Brand: RepRap Printer: Maker Select V2.1 Rafts: Doesn't Matter Supports: Doesn't Matter Resolution: 0.2mm Infill: 20%

I introduce to you, a bolt-on Bowden system I built for my completely (as of now) stock Monoprice Maker Select V2.1 (and this will inherently work for the Wanhao Duplicator I3). Get rid of that moving mass, lessen your vibration, increase your...

A cable cover for the Monoprice Select Mini. ...Suitable to the idea of https://www.thingiverse.com/make/747801.

The cooling system fits snugly between the fan and the extruder.

This kit adds rigidity to your Wanhao i3 Plus, Monoprice Select Plus, and other similar printers. It was created after receiving my Wanhao I3 Plus, following the design of two previous braces for the Duplicator I3 V series. This mod came as a...

This kit adds stability to your Wanhao i3 V1/V2/V2.1, Monoprice Select V1/V2, Cocoon Create and other Wanhao Rebranded Clones of this style. Firstly, thank you to all who downloaded and installed my front-mounted version of this kit. Secondly, for...

Used self threading five M2 16mm and a 3mm and 10mm screw to mount fans and nozzle.v6 plughttps://www.thingiverse.com/thing:6050408slide on dual fan mount:https://www.thingiverse.com/thing:6250296angled part cooling...

Print Settings Printer MP Maker Select v2 Rafts Yes Supports Yes Resolution 0.1mm (100 microns) Infill 20% Notes Printing with smooth jazz playing in the background--it gives it unparalleled quality and remarkable, even magic, abilities. None of that...