morse key and iambic paddle 3d models

Remix of https://www.thingiverse.com/thing:2054230 Changes: - replaced screws for the axes of the paddles by plastic rods from the base to the roof - paddles new designed for: M3 screws with M3 nut; recesses for mounting repulsing magnets instead of...

The clearance between the paddles noses and the buttons can be adjusted to zero with the 2 threaded grains (or also short M3 screws) placed in the rear zone of each lever. The adjustment can be done also on the assembled product thanks to the rear...

Here you have an Instructable to learn how to set it properly: https://www.instructables.com/Morse-Key-Paddles-Iambic-Type/ 73s from EA3HTH ----------------------------------------------------------------------------------------------------- [CAT]...

Use the same paddles and hardware included in OK1CDJ's original design, except the M3x4mm grub screws should be lengthened to 6mm to ensure they never fall out. I used Meshmixer to split, extend and rejoin the part, and Tinkercad to add more magnet...

Mini Iambic Magnetic Morse Paddle is designed for portable or SOTA operation. The original design was made by Vojta OK1IAK, and I made some changes to it. There is an OpenScad source available, which you can modify if you like. Material needed: ...

I constructed a Morse code key using basic components like screws, a hacksaw blade, and connectors. ...The goal was to create a lightweight, disposable key that could complement my portable communication system.

... My version 1 of a 3D-printed key is now complete. ...I required one for an Arduino project I'm currently working on, so I rapidly designed and printed it out. ...It feels fine and operates well, but I plan to make some minor adjustments to version 2.

I moved the 3.5mm opening for the jack to the back side and slightly raised it from the floor, allowing a standard jack to fit seamlessly. Additionally, I incorporated a small channel to accommodate an enameled wire for the GND connection. The GND...

This is a Full Sized Iambic Key That Uses Flat Package Strapping and 1/4" Hardware for An Iambic Key Functionality. The Metal Straps Add Durability, While the Miscellaneous Hardware Ensures a Secure Fit. As a Teenager with an Interest in Morse Code,...

I designed an improved paddle several years ago, but decided to refine it and make the paddles more secure, leading to this V2 model of my original non-iambic paddle. This design leverages a portion of a common hacksaw blade as the spring for the...

Create Your Own DIY 3D Printed Morse Key by LZ1JER First and foremost, ensure that your printer's axes are perfectly aligned. If required, you can easily adjust the orientation during the slicing process of the model. To get more information on the...

This is a small CW Paddle Key It is less than 3.5in long overall. It has provisions for 4 flat head screws to attach it to a surface. It is a revision of my previous design: https://www.thingiverse.com/thing:5402839 UPDATE: I added some paddles...

I broke my paddles on my CW Morse Iambic Paddles, so I reverse engineered the broken ones, and created these. They seem to work well. ...Be careful when resoldering the brass contacts, because if you take too long, you will melt and bend the paddle.

The connector's middle contact should be connected to the "dah" paddle (or the right paddle), and the last connector contact (usually ground) should be connected to the center post in the base. 10. Check the spacing between the paddles and the...

I liked the design but I changed a few things to make it more adjustable and I added a slotted bolt and nut to hold the cable without ties. I only had 10mm square magnets so I changed that and used small tabs that I heated and bent over instead of...

This project, once completed with the addition of a few springs and other necessary hardware, should result in a fully functional paddle for transmitting morse code. Be advised that this is an ongoing project, and as such, no assurance can be given...

A simple replacement paddle for MFJ-564 Iambic keyer. Model is ambidextrous. The mounting holes are designed for 2mm bolt diameter. ...

I have upgraded the paddles to provide a more precise fit for an M4 screw, potentially requiring adjustments that may involve drilling and tapping the existing holes.

 PCB can be clearcoated (or propertly conformally coated, if you have that available) after assembly.It uses the following parts:* 3x6x2.5mm ball bearings to carry the paddles (L630ZZ / MR63ZZ)* #6 ring terminals (I used Wirefy marine ones,...

This is a modification for ReallyBigTeeth's iambic paddles, which should work seamlessly on any model he has shared. The design was printed with precision using 100% infill at an incredibly fine .04 layer height. ... It slides snugly into place within...

Use PC case screws and M3 nuts to secure the wires and paddle levers, no solder needed! I used a 3/16" washer from walmart for the ground/center contact and the paddles are just feeler gauges. I used the existing holes and did not modify the gauges...

Paddled miniaturized on iambic OK1IAK scale.

This manual Morse key is a sleek 3D-printed device that offers precise movement and adjustable force with travel in a minimalist, easy-to-use design. Its compact and lightweight build makes it perfect for taking on the go. Users have a variety of...

American Morse Equipment, DCP Miniature Iambic Paddle Kit base, possible to hold 2 magnets 5x15 mm size. Base for the DCP miniature imabic paddle to prevent connectors. For easily mount, it is possible to fit two magnets in the base. To fit magnets,...

Iambic CW paddle Material: 4 x M5x20mm 3 x M5x30mm 7 x M5 nuts 2 x M4x10mm 4 magnets 5x5x1mm for the paddle return The base was printed with supports. ...

I'm building a compact Iambic morse code key perfect for carrying in your pocket or backpack. This design utilizes an old hacksaw blade for added durability, secured with just three simple M3 screws that fit perfectly into their mounts. ...Version 2...

Finger pieces for the Vibroplex Cube Morse paddle, and possibly other Morse paddles as well. The included DXF file allows for easy laser cutting from either 3mm plywood or acrylic. ... Also provided is an STL file for those who prefer to 3D print their...

Wireless Interconnected Protocol Morse Key

This is a 3d printed base and cover to store your World War 2 MKIII Morse Key.You need M3x15mm bold and nut and 3.5mm audio jack to connect your morse key and access it using just audio cable.

We've got a new version of the mini paddle out now - check it here: https://www.thingiverse.com/thing:3220538 Take a look at this video to see the key in action: https://youtu.be/Hm7rOoXqPUg Get in touch with any questions you may have.