mosfet breakout 3d models
5287 3d models found related to mosfet breakout.thingiverse
This is a smalll breakout board featuring two logic-level MOSFETS for driving any sorts of heaters, DC motors, solenoids etc. It has been successfully tested as a spindle driver with 32 KHz PWM and a 27 V power supply. I haven't seen any problems...
thingiverse
This is a clip to hold the Mosfet breakout board from SparkFunhttps://www.sparkfun.com/products/10256 I'm using it for the g-code enabled extruder fan mod on my Solidoodle 2. Details on how to set it up can be found...
thingiverse
This is a Mounting pad I made to mount my HA210N06 Mosfet Breakout Board. If you use this make sure you use short screws so they don't poke out the back and touch what you are mounting it to. I used 1/4" No2 screws. I added a V2 (I had it a while...
thingiverse
If you need more channels look here: http://www.thingiverse.com/thing:163580 Simple MOSFET board with galvanic isolation. This could be usefull if you want the power supply for the heatbed to be isolated from the printer power supply. NB: This has...
thingiverse
Holder for XY-MOS D4184 Power MOSFET breakout module. Snap-in, no screws are needed to hold the module in place, but holes for small screws are included for extra security. ...I used 1.8*5.6mm sheet screws.
thingiverse
Cette piece permet d'installer sous votre alfawise U30 2 mosfets ils vous faudra des TNUT m3 : https://www.thingiverse.com/thing:1729060 afin de les fixer, veuillez noté que vous devriez ajouté de legere modification si cela ne convient pas
thingiverse
Simple, quick print to mount a Mosfet breakout board to the Power Supply Unit (PSU) that came standard with my Anet A8. May fit other PSU. Allows clean mounting behind the Anet A8, to manage and shorten the 12V supply wires, instead of running all...
thingiverse
A remix combination of polysquare's 120mm fan mount adapter that "lets you mount a 120mm fan to the back of the control box / PSU of Wanhao Duplicator i3 (Monoprice Maker Select V2)" combined with Taxus812's MOSFETpad for the HA210N06 Mosfet Breakout...
thingiverse
This is an accurate model of the AMG8833 breakout. ... Perfect to use when designing your projects, housings, and so on.
grabcad
model ASD-BM-50ANote:Breakout board that can be used with Delta ASDA-A2 systems for wiring the CN1 connector. ...It could probably also be used on other brand servo drives, but the labels on on the terminals are made for ASDA-A2
thingiverse
This is a first attempt at a Microbit breakout connector. I was aware that the GPIO pins on the Microbit are too narrow to fit jumper wires on one side of the board so I tried to make a row on the other side of the board - only then discovered the...
thingiverse
A script to generate snap-together holders for Sparkfun breakout-boards. The size is chosen specifically to agree with the Sparkfun polygonal proto-boards. This, however, isn't compatible with my previously published dodecahedral protoboard thing:...
cults3d
A script to generate snap-together holders for Sparkfun breakout-boards. The size is chosen specifically to agree with the Sparkfun polygonal proto-boards. This, however, isn't compatible with my previously published dodecahedral protoboard thing:...
prusaprinters
I wanted to take the load off my board and chose this Mosfet from Amazon.I use it for the Heatbed.Printsettings:SupportnoRaftnoFilamentForm Futura “CarbonFil - Black”Layer0.2mm with 4 Perimeters & 30% Infill
thingiverse
Listings come and go, but the current listing title contains the text "MOSFET breakout board module switch relay (15A, 60V) 3-outputs for Arduino/RPi". These modules provide three MOSFET switches that can be used with a 3D printer, Arduino,...