mouse bungee 3d models
16071 3d models found related to mouse bungee.thingiverse
3D Printed Mouse Bungee that uses two 8mm ball bearings. ...Works better than my Razer Mouse Bungee in my opinion https://giphy.com/gifs/SsCrBfNrxa4PLUNDJf/html5
thingiverse
2-part mouse bungee dedicated to a 17mm thick desk. ... Print on flat surfaces using supports
thingiverse
I made a mouse bungee. You can use it by putting a spring in the round part in the middle. ... spring Size ~6mm Upload 2020.11.13
cults3d
... from bothering you during your work, gaming, recreation, or whatever you may do! I spent many hours designing this so that it would print nicely and serve its function. Mouse bungees are outrageously expensive for what they are (about $20-30).
thingiverse
Mouse bungee This bungee work with a 19mm tickness desk, He is compatible with a 3mm mouse wire (most mouse are 3mm wirered) reso 0,2mm With support infill 30%
cults3d
... I added a second version with higher tolerances, in case the thread of the original version is too tight for you. "Mouse_Bungee_Body_loose" and "Mouse_Bungee_Lid_loose" should work better for printers/slicer/materials that need higher tolerances.
thingiverse
... I added a second version with higher tolerances, in case the thread of the original version is too tight for you. "Mouse_Bungee_Body_loose" and "Mouse_Bungee_Lid_loose" should work better for printers/slicer/materials that need higher tolerances.
myminifactory
________________________________________________ EDIT:I added a second version with higher tolerances, in case the thread of the original version is too tight for you."Mouse_Bungee_Body_loose" and "Mouse_Bungee_Lid_loose" should work better for...
thingiverse
Hello! ... Another one mouse bungee. I was inspired by this bungee (https://www.thingiverse.com/thing:2832887) and made a new one for me. ... Also, the fusion 360 project file included.
cults3d
... This bracket will prevent the mouse cable from bothering you during use. . Mouse bungees are outrageously expensive for what they are (around $ 20-30), so I offer this one very cheap. ... It has a design with the logo of the Rainbow Six Siege game.
thingiverse
I made a mouse bungee. You can use it by putting a spring in the round part in the middle. ... Spring size ~6mm Screw hole size M3 Upload 2020.11.13
thingiverse
This is a mouse bungee I made inspired by the Razer mouse bungee V2 but not expensive. Here's of video of it working: https://youtu.be/IuhN_GQQ2Ok Here are the instructions: 1. You need to buy this spring and cut it in half so each length is...
cults3d
MOUSE BUNGEE Mouse bungee is used to keep your mouse cable in place and avoid you to problem with pulling mouse in game time to have propelly cable distanse. This model need extra elements, springs, and pins, nuts Please feel free to share your...
thingiverse
Hello, this is a mouse bungee that can be mounted to the table. The Horizontal Expansion setting is important for the screw and the base. You can scale the arm.stl down a bit for a loose fit. Every thing prints great without support. ... If...
thingiverse
I remixed the mouse bungee because of my mouse cable is so thick and i can't use it so I made 3mm cable, and 4mm cable version and lighter and original version it's ok to print without support' and make sure to set infill 100% when printing original...
prusaprinters
I wanted to have a mouse bungee so I created this simple project. To build it you will need one 100 x 16 mm spring, two M3 screws and small zip ties. ...I included .f3d and .step files so you can make it fit any spring you have.</p><p> </p>
thingiverse
I made this mouse bungee because i wanted a bungee that does not need tape or weight. You just place it slightly under the mouse pad. Printed in pla, all you need is a small m1.5 skrew(or similar, hole is 1.5 mm) you can also just glue the parts...
thingiverse
Mouse bungee a tried with my Logitech G502. I have just tried to print one and test it with my mouse and it works so far. The feet is placed under my mouse mat and it works. In next version i will make it so the cable can be attached on the feet...
thingiverse
A quick little mouse bungee design. I used hot glue to affix it to the desk, however 3m double sided tape would probably work as well. I also used a dab of blu tack or poster tack to secure the mouse cord. Printed with the tower flat on the printbed....
prusaprinters
Remix of my original mouse bungee with added cut-outs for 12mm diameter bumpons for desk. Added STL for people who want to edit this.</p><h3>Print Settings</h3><p>0.2mm, Brim, 80% infill</p><p><strong>Notes:</strong></p><p>Rotate 220 degrees on the Y...
prusaprinters
Looking for a smart way to hold your mouse cable in place? Try this mouse bungee! Just print both files, put the cable in between and screw the parts together. You can use double sided tape to fix it on your desk or a M3 screw to place it on the...
thingiverse
Created a mouse Bungee to attach to the back of my desk, and thought I would upload it in case anyone else wanted to use it! It is designed to hold standard 3mm cables well, but if your cable is slightly bigger or if the cable holder part printed...
thingiverse
This is Mouse Bungee for better cable management. Cable mount should work for 2.5-4mm cable thickness. To add some weight, drill holes at the bottom and apply some plaster/concrete. Add rubber/silicone feets to prevent sliding on the table. Print...
cults3d
Bungee Mouse inspired by Razer V1 model You need the following spring: Length: 150mm Outside diameter: 8mm Wire: between 0.8mm and 1.2mm (ideally 1mm) The base is very easy to fit and has spaces underneath to put a double-sided tape so you can stick...
thingiverse
This bungee has 4 holes in the base for put some neodymium magnets, then you can put a magnetic sheet under your mousepad and the bungee will stay fixed to the mousepad.