moveable 3d model

The pilings for this model are 20mm - slightly shorter than for Huts 1 to 4. If you want an easier time of it, you could just print shorter independent pilings, so the huts are not raised so high and its just a single step up into them from ground...

The pilings for this model are 20mm - slightly shorter than for Huts 1 to 4. If you want an easier time of it, you could just print shorter independent pilings, so the huts are not raised so high and its just a single step up into them from ground...

... most of these parts. If there are any tweaks necessary let me know. I have added a .step file of the assembled printer and I will upload a Fusion 360 back up file as soon as its processed so you guys can go nuts customizing the solid models.

The pilings for this model are 20mm - slightly shorter than for Huts 1 to 4. If you want an easier time of it, you could just print shorter independent pilings, so the huts are not raised so high and its just a single step up into them from ground...

Anyways, this is getting out of hand so here's the important stuff: Many models to choose from! 18mm sensor 12mm sensor 8mm sensor Then choose you cap: 2 stock fans with chain mount 2 stock fans no chain mount No fans no chain mount No...

**Just make sure they are all the same voltage and be very carefully** - **3S BMS 20A** - I used the HX-3S-FL20 REV2.2 Probably they are more models similar to this, this was the name I found. This is for controlling the charge and discharge of the...

It started with a Bachmann starter set with a steam loco and a couple of cars (Durango & Silverton in case my other models didn't give it away). This came with a bunch of EZ-track. I had full intention of expanding my layout so I bought more...

http://www.thingiverse.com/apps/customizer/run?thing_id=368375 Instructions Using the following options: custom_bottom_port_x_position = 20 custom_back_camera_corner_resolution = 8 stencil_horizontal_position = 50 custom_bottom_fillet_resolution = 8...

Will require manual tapping. Base Base_Type - The type of base (round or rectangular) Screw_Hole_Diameter - The diameter of the screw hole Screw_Head_Diameter - The diameter of the screw head Screw_Head_Countersink_Angle - Screw countersink angle...

All overhangs should be 45 degrees or less. Rafts: Not required, unless you experience adhesion issues. License The "Hard Drive Holder" models (.stl) are licensed under the CC BY license by Code and Make. The "Hard Drive Holder" code (.scad) is...

The COMPLETE Requiem Brotherhood bundle contains every model of this set, from the modular units to the heroes, the mount, the Pinup and the terrain piece! This set includes: Requiem Templars (presupported) Requiem Templars stand before the chaos and...

being able to reprint the broken part vs the entire model is a plus. Except for the charging ports, no glue is needed. All the STL files have been positioned to hide the seam as much as possible (when possible). The Activator Assembly parts are...

The COMPLETE Dragonpeak Barbarians I bundle contains every model of this set, from the modular units to the heroes, the mount, the Pinup and the terrain piece! The people of Dragonpeaks are direct descendants of the Humans who lived in Aera under...

The COMPLETE The Bloodhunt bundle contains every model of this set, from the modular units to the heroes, the mount, the Pinup and the terrain piece! The Bloodhunt Knights were the first Soulless Vampire troops to be sent to the mortal lands of...

The human element is a crucial aspect of most systems and models, providing a personal touch that helps users feel more connected to the technology they interact with. By incorporating human-like features, developers can create products that are not...

First, I modeled the front of the display to fit the RepRap Discount Full Graphics Smart Controller. Then, I also decided it needed a back to protect the circuit board. Easy peasy! Next, I tackled the problem of mounting a TFT35 touch screen...

My O scale model train layout represents the section of the Pittsburgh & Lake Erie Railroad between McKees Rocks and Youngstown. This wall section (stretcher bond brick pattern) will let you assemble a background flat of the McKees Rocks...

The COMPLETE Swamp Gurunda bundle contains every model of this set, from the modular units to the heroes, the mount, the Pinup and the terrain piece! Swamp Gurunda (Presupported) The amphibious people of the swamps, with slimy skin and innate...

Not suitable for heated chamber!Below are the temperature results of what I tried************************************************************************************* Notes:The Top_Rods_Cap.stl have a groove preventing 180° rotated insertion (they...

Print so that the models are standing upright, largest end down. <h3>Post-Printing</h3> <p>To disassemble the original turn signal, follow these steps:</p> <ul> <li>Remove the screws securing the lens and remove the lens.</li> <li>Remove the...

Merry Christmas! You will need to print: 4 ea Whirligig blades 3 ea Eccentric cams 2 ea Crossbars 2 Reindeer 2 ea Base Couplers 1 ea all other parts There is a cutaway view in the thing files called cutaway view.pdf showing how the model goes...

There is also a reverse mount for the hygrometer that's for mounting it on the inside of glass (also fits stock model).The hygrometer has an extender for the button that switches between C\F. You will need the original rubber insert...

These are mainly meant for kitbashing digitally, so they might not work with existing citadel kasrkin/cadian models without a little work. For torsos I suggest Planetless Trooprs by LoggyK, these were the main inspiration behind the packs. Storm...

The bowl model is a solid piece, and CAN be printed in vase mode / spiralize outer contour. This, however, isn’t the strongest. What I do is print them with 0% infill, 2-3 outer walls, 4 bottom layers, and 0 top layers. Basically makes it a double...

... for all of this - I am just starting to learn with Onshape thanks to TeachingTech's new series but Tinkercad is still a lot quicker for me with these simple shape kind of designs. I am looking forward to being able to create more detailed models :)

http://www.thingiverse.com/apps/customizer/run?thing_id=368375 Instructions Using the following options: custom_back_extra_port_corner_radius = 5 custom_right_port_y_position = 0 custom_left_port_corner_radius = 5 custom_bottom_port_corner_radius = 5...

A perfect fit for your specifications, this model features the following options: picture =...

Would like to thank Okef256 for the original model. &nbsp;It doesn't seem to get much attention, but it is great.</p><p><strong>Modifications:</strong></p><ul><li>Modified mount to attach to Ender 5 mount plate instead of linear rails.</li><li>Added...

Lightweight PLA tool is non-conductive, non marking and wont damage your materials if dropped the same as a heavy chunk of aluminum will.&nbsp;&nbsp;Files Grouped in 5 Categories:MK3S+ Gcode Pre-Sliced - combined : All Files to build everything pre...

The body and base were printed on my CR-10S. Layer height: 0.12mm, Nozzle: 0.4mm, Perimeter: 0.8mm, Speed: 60mm/s, Top/bottom # layers: 6, Print time: I honestly can't remember... The head was printed on my Ender-2. Layer height: 0.12mm, Nozzle:...