multiply model

Most LEDLB, LEDP10W and LED10W series lights ship with mating connector as part of a harness or pigtail, depending on the model. Some larger LED lights like the LEDLB-160X2 or LEDLB-200X2 or multiple function LED lights (i.e. ...high/low beam,...

http://www.thingiverse.com/apps/customizer/run?thing_id=368375 Instructions Using the following options: custom_bottom_port_x_position = 20 custom_back_camera_corner_resolution = 8 stencil_horizontal_position = 50 custom_bottom_fillet_resolution = 8...

... everything is still a live boolean cut or unity, to edit things easily, but slows down things a lot. If you like what I do, feel free to support me, any tip will help buy filament to test prints or spend more time on improving models- thank you

Some parts need supports for countersunk screw holes, or other parts that are not supported by the model or the bed. Use your best judgement, or use PrusaSlicer and the provided .3MF file, which I have pre-configured with supports in the needed...

http://www.thingiverse.com/apps/customizer/run?thing_id=368375 Instructions Using the following options: custom_right_port_y_position = 0 custom_top_port_corner_radius = 5 custom_left_port_length = 50 pattern_element_rotation = 0...

Most issues with these printers can be traced back to this strain gauge probe not functioning properly.It would be convenient if their mainboards were compatible with the CR-touch / BL-touch probe style sensors found on the newest higher end Creality...

I first encountered the idea for this type of robot in a biomedical article, presented as a potential new candidate for exploring the human colon due to its simplicity and ability to navigate confined areas....

This requires a solid fill model where only the walls are printed. Several changes were made to the CR-3D C8.1 design, including re-engineering the STL file and making ergonomic tweaks based on user feedback. The sides have been extended back to...

I also adjusted the tolerances of the nozzle wrench brackets so that they fit a bit tighter.I also felt the cover did not latch securely enough, so I also deepened the magnet pockets on the case, so you can stack two 6x3mm magnets in each pocket.I...

I think the steel should slide easily against most rigid plastics but better safe than sorry. Use Instructions: Print the model Remove the heat sink, tubes, retaining screws, and any heater or thermistor -- only the hot block and heat break should...

http://www.thingiverse.com/apps/customizer/run?thing_id=368375 Instructions Using the following options: custom_right_port_y_position = 0 custom_left_port_length = 50 custom_top_port_corner_radius = 5 pattern_element_rotation = 0...

This model is extremely water-resistant, highly buoyant, and accelerates quickly with my setup. I printed this on my Ender 3 using split parts for easier printing or a single part if your printer can handle the height. The hatch measures 26mm deep,...

A wrench is used to unscrew the end caps for relamping the fixture, while some competitive models require the “tap and knock off” method to loosen the end cap. 7. Explosion proof, impact and heat resistant Pyrex tubes provide lamp protectionSuperior...

Scaling: The model as is in the STLs will accommodate most types of earbuds, however it can be scaled down as much as 30-35% for smaller sets. If you use earbuds with an inline control, such as the ones shown in the pictures, the standard STL size...

Use "leveling_test.stl" model to test auto-level accuracy. I made some work tests of this firmware but there still could be bugs there, so use it on your own risk. Enjoy! Update 1: My Start and End G-codes in Cura working well with this firmware: ...

All overhangs should be 45 degrees or less. Rafts: Not required, unless you experience adhesion issues. License The "Hard Drive Holder" models (.stl) are licensed under the CC BY license by Code and Make. The "Hard Drive Holder" code (.scad) is...

http://www.thingiverse.com/apps/customizer/run?thing_id=368375 Instructions Using the following options: custom_back_camera_x_size = 20 custom_bottom_port_x_position = 20 custom_bottom_port_corner_resolution = 8 stencil_rotation = 0...

http://www.thingiverse.com/apps/customizer/run?thing_id=368375 Instructions Using the following options: custom_left_port_corner_radius = 5 pattern_element_rotation = 0 custom_top_port_corner_resolution = 8 custom_right_port_corner_resolution = 8...

The COMPLETE Dumlok Flameseekers bundle contains every model of this set, from the modular units to the heroes, the mount, the Pinup and the terrain piece! This set includes: 12 Dumlok Flameseeker (modular figures + figures with helmet)The Dumlok,...

If you need to use a different pump you can model and print your own adapter as it is just a rectangle block with a hole for the pump water outlet. The inlet block should be 80mm tall and 32mm wide minus half a millimeter for fit tolerance. If you...

License ------- The "Bitten Doughnut" models (.stl) are licensed under the [CC BY](https://creativecommons.org/licenses/by/4.0/) license by [Code and Make](https://codeandmake.com/). The "Bitten Doughnut" code (.scad) is licensed under [The MIT...

R/Cers there are included ailerons for micro setups!\nNotes: On my printer (which isn't working so great right now) this works out to 3 and 4-layer parts (mostly), so the whole thing took about 1/8 spool of filament, and all of it prints in about 4...

I downloaded and printed two of the Flugzeug Halter - Breit STLs in the Model Plane Ceiling Hooks thing from dschiedsch. They worked but were a tight fit for some planes when I tried them out. That is when I decided to make something adjustable to...

The new model isn't uploaded yet, but stay tuned for updates. 6/25/20 - This device has proven too effective. If left in the water for an extended period, it rapidly consumes the anode and produces copper oxide flakes. I can only leave it in for a...

http://www.thingiverse.com/apps/customizer/run?thing_id=368375 Instructions Using the following options: custom_phone_thickness = 10 custom_back_camera_x_position = 0 stencil_pattern_element_overlap = 0 custom_top_outer_edge_chamfer_radius = .6...

They can compare the forces involved to what computer models predicted. rnd. Students can use solidworks to predict and measure stress and loading on them.rne. Students can explore redesigning these to be lighter, use composite material, or have...

http://www.thingiverse.com/apps/customizer/run?thing_id=368375 Instructions Using the following options: stencil_drawing =...

Print Settings: • Ensure the model is orientated as shown in the slicer image • Skirt - Yes • Skirt Line Count - 2 • Skirt Distance - 1 mm • Support - Yes • Support Placement - Touching Buildplate • Support Pattern - Lines • Support Wall Line Count...

...The design is optimized for the given print orientation - no need to rotate the STL model.You will also need two of the strain relief clips, which I have provided as a separate project.Assembly6 pieces of M3 nuts have to be pressed into the plastic.

A wrench is used to unscrew the end caps for relamping the fixture, while some competitive models require the “tap and knock off” method to loosen the end cap. 7. Explosion proof, impact and heat resistant Pyrex tubes provide lamp protection.Superior...