multiwii and megapirate aio flight controller 3d models

To accommodate various flight controller configurations, two versions are available: straight and tapered, with the tapered version featuring an extra 6mm on top for improved clearance. To achieve optimal results, printing these mounts with 100%...

The second standoff is to go between a 4in1 ESC (normally at the bottom of the stack) and the Flight controller (at the top). The spacers are bevelled and intended to be used with rubber O-rings washers (probably 4mm x 2mm) to provide damping. I will...

A second standoff is intended to fit between a 4in1 ESC typically located at the bottom of the stack and the Flight controller positioned at the top. The spacers are intentionally bevelled for use with rubber O-ring washers, likely measuring 4mm x...

A standard-sized (30x30) flight controller mount that fits perfectly into place. The stand-off distance is 4mm, ensuring a sturdy hold. Threaded holes are designed to securely fasten with your preferred hardware. Minimal vibration dampening is...

A straightforward 30mm flight controller mount that I use to securely attach gyro components to frames lacking the standard 30mm mounting holes. To ensure a precise fit, I've updated the design to correct the centre-to-centre length from 30mm to the...

Softmount designed specifically for quadcopters' flight controllers features a 3mm hole to securely attach it to the frame screw. The plug fits perfectly into the fc's 3mm holes and locks firmly in place. The distance between the upper and lower...

Model of DJI - A3 - Flight Controller prepared for needs of Sevendof AS for development purpose due to lack of officially released of the geometry by DJI.Released with employer permission under Apache 2.0 License.The model includes the DJI Logo and...

I just needed a means to securely fasten my flight controller to some foam without having the standoff nuts protruding, so I created this design with a flat base that can be easily glued into place. ...It's a swift, uncomplicated solution that gets the...

Soldering Fixture for Standard Flight Controllers (36x36mm). Print Settings: Printer: Select Fabrikator mini. Rafts: Choose No. Supports: Select No. Resolution: Opt for either .1mm or .2mm precision. Infill: Set to a minimum of 40%.

Adapts a compact 15x15 flight controller mounting from a standard 30x30 design, utilizing TPU as the printed material, though other filaments can also be used effectively. ...The original mounting holes were M3 in size, while the resized version...

Here's a simple O-ring design for your flight controllers, so don't forget to use TPU - no supports required! I printed this at a layer height of 0.1 mm. ... Hit me up via email at 168mcz@gmail.com for instant feedback.

A set of spacers designed specifically for FC use with 30.5mm holes is available. The spacers featuring a 3.5mm clearance are intended for use in the following configuration: QUAD FRAME > 2mm NYLON NUT > 1.5mm PDB > SPACER. ...Note that the F3 protector...

I designed this flight controller (FC) adapter for my quadcopter build. My FC is a KK board from Hobbyking that has a 45mm hole spacing, but the frame I bought has a 30.5mm spacing for mounting the FC, probably with an FC like a Naze32 in mind, which...

I designed this flight controller (FC) adapter for my quadcopter project. My FC is a KK board from Hobbyking, which has a 45mm hole spacing, but the frame I bought features a 30.5mm spacing for mounting the FC - likely intended for an Naze32, a very...

Case for F4BY v2.1.5 flight controller still usable despite lingering issue with disposable covers for connectors. Disposable covers work fine when they're discarded, but there's no room to accommodate plugs inside the case with a wire harness passed...

DON'T EVEN THINK ABOUT BUILDING IT; IT'S A PIECE OF JUNK; THIS IS JUST A COLLECTION OF HALF-BAKED IDEAS\nTHE JOYSTICK IS A MESS, IT'S STILL IN THE DEVELOPMENT STAGE AND NEEDS A LOT OF WORK\nA sleek Joystick (Blisstwig, I had to use a thesaurus for...

I recently came across an innovative method for eliminating vibrations on my FC controller through a video tutorial. However, upon examining the original design, I noticed that it does not provide any means of securely locking the FC to the TPU...

Print twice. ...Requires short M3 inserts and M3x8 screws.

I completely reimagined the design, since the original seemed flawed and refused to slice cleanly with Simplify3D's software.

... to standoff. ... Usage: Perfectly suited for Top Deck, Protector, and Platform applications. Print Time: Achieved in just 10 minutes. Printing Notes: Successfully printed in PETG without supports, utilizing a 0.1mm resolution and 75% infill density.

Redesigned the circuit after totally understanding the circuit design and program code of PIXHAWK, achievedless interference of inner components, less noise, more accurate compass and safety while flying, resolvedthe problem that Altitude Hold was...

... Infil to add weight. Full print with 4x4x4 walls/top/bottom and 38% infil came to about 48g in weight. Glue in lettering and spade. ... Star may need minor sanding but should push fit into the space tightly and not need anything else to secure it.

Updated model with CUBE Orange f/cDimensionally accurate CUBE Orange standard carrier board.CUBE Shell and tray provide secure physical protection - as used on the Ranger Q700http://highceeaerotech.com

There's nothing particularly unique about this, it was mostly just to fit the hardware and placement I wanted. And if the TPU snot on the print was enough of a clue, I'm new to printing with TPU so I figured this was just as good a reason as any to...

Flat Version and 3mm Spacer Versions Available The following versions of the FC Spacer are available for download: *A flat version, which can be found in the file fc_spacer_flat.stl *A 3mm spacer version, which can be accessed through the file...

... specifically for the latest iNav build series, which enabled me to securely attach the FC to the 'plane with ease. ...It perfectly accommodates any FC or PDB measuring 36mm by 36mm in mounting hole size and is ideal for a seamless glue-in installation.

... snugly onto a standard 32mm stack, serving as an essential accessory for various applications. ...In situations where extra cable management is required, it proves particularly useful by providing a secure and organized way to keep cables in position.

Before I start any new quadcopter build, I always print out this spacer pack so I can get the FC stack as compact as possible, especially in the new super slammed builds. ...Spacer sizes are all for M3 hardware and their heights are 4mm, 5mm, 6mm, 7mm.

It stands at an impressive 8mm tall and boasts a diameter of 7mm, featuring a precise hole measuring just under 3mm in size. The screws used may not thread smoothly into the standoff, but they provide a secure grip nonetheless. ...This solution has...

Use your PS5 Controller on Flight Simulator 2020 with "ds4windows" and a 360 Profile This Joystick will help you to control your flight a little smoother :)