music stand for keyboard 3d models

... I noticed that they sometimes fall over at night. To prevent this issue, I created a stand specifically designed to hold PC keyboards in place without falling. ...My design features three or more shells and 20% infills, printed at low resolution.

This is just a keyboard stand. ... Print 2 or more to use.

This is a replacement knob modeled from an On-Stage A-frame keyboard stand.

This is a high-quality replacement stand specifically designed for the CoolerMaster Masterkeys Pro keyboard series. It was thoroughly tested on the Pro M version, but it should also be compatible with other versions of this keyboard and any other...

This is a stand for an Apple Magic Keyboard. There are 3 files. The entire keyboard can be printed as one piece if your printer is big enough. There are also files for the left and right halves because the Ender 3 Pro is not large enough to print it...

This is a simple stand for keyboards without feet (e.g. diy). ...The angle can be adjusted by changing where the feet are plugged in.Successfully printed in PETG using Cura and Ender 3.

Stand for displaying a keyboard. No issues with bed adhesion. Print 2 of each part. ... You may need to file down the pegs and the holes a bit to make them fit.

Wireless Keyboard Storage Stand. could be used as a tablet stand. ...Pretty basic but it does the trick.

This is a stand for a custom PCB keyboard found here: [github.com/Envious-Data/Env-MCRO](https://github.com/Envious-Data/Env-MCRO) It utilises a Raspberry Pi Pico and a custom printed PCB found on the GitHub page. ... The idea was to create a Stream...

Replacement Keyboard foot for "Wired RGB Gaming Keyboard, Membrane Keyboard with 8 Independent Multimedia Keys, 25 Keys Anti-ghosting, Plug and Play" off of amazon.

... on a shelf. ...The parts were designed with no tolerance and fits tightly. You can print the full assembly for a single stand or these per stand: * Keeb Leg x2 * Connector x3 I've also designed a 3-keeb stand, for that, you'll need 6 connectors.

... cutting. ...I use it as keyboard stand or artisan keycap box stand but also for my phone. ... The 60mm refers to the distance between the legs and the hex design is mostly just to maintain structure but use less material than solid bottom/backs.

This handy phone stand can be mounted directly to your keyboard to have direct access to your phone. You can use it to use your phone as a stream deck or as media control center. I use it to have access to companion apps for games. The back...

Keyboard stand for HP KB57211 Keyboard, as it's often stolen or broken, replicate them using this model. With exact measurements, no surface lines, single faces, and adjustable clips for easy installation. Print Settings: Printer Brand: MakerBot...

I needed a way to free up desk space on a slightly cramped desk. I printed this in Inland White PETG with the following settings:0.3mm Layer Height (Draft)3 Perimeters4 Top/Bottom Layers20% Gyroid InfillPrint time was about 2h15min.I have uploaded...

... No supports, no rafts. Print in lower resolution to save time. On my MK3s it took exactly 1 hour to print 2 of them at .30 (draft). Increase or decrease the size in your slicer if they aren't quite large enough for your particular keyboard.

Same files as the remix, but I added a lip as my keyboard kept slipping off the stand.

A versatile and adjustable keyboard stand crafted from the ground up using Fusion 360's robust design capabilities.

Modular version of the keyboard stand to suit different keyboard sizes. I found the original to suit 60% and 65% keyboards well, but not longer or shorter sizes. Print one of each piece, but pick the middle piece depending on your keyboard size:...

Adjustable Keyboard Stand. ... This versatile stand offers two nut sizes, short and long, allowing users to customize their setup according to their preferences.

Desktop keyboard stand one stand had broken following a move so I measured and drew from the other to print a version

I needed a way to hang my headphones on my Millennium keyboard stand. ...This is just a simple remix, where I added a hook to a pre-existing design that fitted the keyboard.

I had no clue why my nine-year-old daughter wanted this, but she specifically asked for the stand to hold her Mac keyboard at a 45-degree angle. To be honest, I think it's pretty hard to type on your laptop at such an angle - personally, I find it...

Phone/Tablet Stand for Logitech K520 Keyboard.\r\n\r\nEdit January 27, 2018.\r\nA revised design is now available with shorter versions that provide a bit more space around F keys and feature a rotated model for easy slicing.

Lifts Apple keyboards at an angle. ...Tested with a few different models of magic keyboard. ...Sketchup project included for easy remixing.

Worked for all my keyboards but as it is fairly small it might not work for heavier and larger boards. (tested with a 1.5kg KBD75 and it worked fine) The fitting is loose on purpose as i wanted this stand to be easily disassembled for storage or...

This is a replacement sleeve for a Roland keyboard stand. I printed it in TPE88 with 50 % infill, the flexibility seems to be roughly the same as the original part. ...I had to use a brim, otherwise the print would curl up and wouldn't stick to the...

This ergonomic keyboard stand was specifically designed for a student with disabilities who struggles to type using her fingers. Instead, she relies on a stylus held in her mouth to press each key, so the stand must hold the keyboard at an optimal...

I created a custom keyboard stand/foot to replace the one that broke off from my Trust keyboard. I'm not sure if this design will work with other keyboards, but it should be compatible with most standard layouts. ...The infill on this model is set at...

A simple phone stand that allows it to sit over a keyboard. I primarily designed it to allow the keyboard to slide under it to make more room in front of the keyboard. ...It should work with most phones and it also works with most tablets or e-readers.