n scale 3d print files

the 2 blue parts are glued together with the pivot in between and there are a couple of 2mm holes to add some printer filament into as a dowel and guide. the silver part is the magnet and shows the hole it goes into and orientation, the black part is...

There is a many video about how to do it. Is not difficult but may change depending on what cable you chose If You enjoyed this project and You want to say "Thank You" please consider supporting me by sending a tip on thingiverse or my PayPal here. I...

 Print Instructions:Material: TPUWalls: 2Top/Bottom Layers: 0Infill: GridSpeed: 70mm/s*Flow %: 98-100% start with 100, and if it's hard to connect the parts together work your way down.*TPU has an upper and a lower speed limit. 70mm/s worked for me...

In the end, it probably does not matter and you can use PLA or PET for any of the pieces. Bill of materialsThe printed piecesM6 screws and nutseither M6 screws with hexagonal head and nuts or star knobsor other M6 screws (max. about 25 mm) with...

Print this out flat, without any supports, and add a 1/4" X 3.5" long nut and bolt to complete the job. If you're wondering about that undercut on the tool, it's there so the gauge slides over hammer strikes on the edge of the Bowen nut - preventing...

I would print the model as it already lies, then you don't need any support. The tensile forces act obliquely on the layers, should fit. Use PETG or ABS. Suggested mounting With two pieces each of M5 anodized aluminum screws with flat Torx...

I have also added a version of the plugs with a vent hole, and a plug for the hole (should be printed in TPU). This allows you: - take the closed scrubbers and sensor head with the cover and vented plugs fitted onto flights, without the plugs...

(unfortunately I don't know the source anymore) After the first stars were ready, a narrower version without any jagged sides should be created. So you can choose whether a whole star with side points should be made or a star with flattened side...

tree supports "touching buildplate", there is a flat side to these parts, i recommend printing them on that flat side. the bottom cap is gonna be tight when giving it the final twist, just undo it and redo it a few times to help it go on all the way....

If you want it to have one continuous rod or multiple ones.Although I made this spool holder to upcycle a damaged 37mm smooth rod (fits for a double spool holder) you can use any other 8mm rod if you don`t have a damaged smooth rod lying around.What...

All parts were printed on a CR-10 with Matterhackers Tough PLA, using 6-8 solid layers and 100% to 75% infill depending on the location. The rocket flew successfully to an altitude of 2800 feet on a J450 motor, with a final weight (without motor) of...

Unfortunately, my printer won't be able to print it anymore. But as it turned out, there is a need for such tools. ... <hr> <a href="https://s.click.aliexpress.com/e/_A3AfNQ" target="_blank"><img...

This was also my first multi-device charger design to feature a “removable power core” that you can take with you when traveling. Parts needed to make it: Qi Coil PCB -...

The RoadRunner should be fully rules complaint but check dimensions before using this design.Note: At time of upload, the design has not been tested in competition and has no guarantee of...

Nozzle changes can be done exactly as before, and by using higher performance tubing allows the stock hotend to reliably print at higher temperatures. Due to the low temperatures at the top of the heatsink, PLA is perfectly adequate for the spacer. A...

(Future remix maybe; I don't want to invest more time in this project) I would also recommend printing with a high infill (as much as 100%) to make it heavier so that it flips better. ...Using locknuts for the bolts holding the blade on would be...

So, I'm taking my first crack at this and being a bit of a BMW enthusiast, and also really stoked with all the other BMW-related prints I found, I thought I'd try creating a dynamic air scoop for my 07 335xi. The scoop sits in front of the rad and...

Schiebt man das Pad wieder zurück in den Gleiter, wird der Ring ebenfalls mit zurückgezogen, so das der Ring nicht übersteht. Print Settings Printer: Anycubic Mega X Rafts: No Supports: No Resolution: 0,2 Infill: 30% Filament: egal PETG / ASA / ABS...

... remade countless times I suspect the model still isn't perfect, feel free to improve / fix. Model includes a version with a flying base, and simple version without a base, and a version with a hole and a separate base for printing separately. ...

So I'll probably try to adjust the two bolts on the bottom and see if there's margin to move the bed another 1.5mm.== Update 2 ==I've included more sizes, I'm printing all of them today and testing how far I can go, the 7.5mm one would eliminate the...

I used PETG, if you use PLA print it solid. No Support is needed. 1. Cut a 30mm piece of PTFE tube and place it inside the mosquito, make sure it's not too short, there should be some pressure when fitting it with the filament guide. <img...

Most of the printed wheelsets work first time, with only occasional wheels proving to be wonky after first assembly. I have experimented and can make my own spiked axle using 2mm brass rod, a dremel and a whetstone. I wouldn't recommend it though,...

The academy's collections comprise over one thousand paintings and three hundred sculptures, along with approximately five thousand five hundred drawings and a collection of prints and medals. However, the current number of works housed in Palazzo...

This would open up some additional mounting options and would be very useful on multirotors. Transmitter used: http://www.amazon.com/gp/product/B00WQZNZ54?psc=1&amp;redirect=true&amp;ref_=oh_aui_detailpage_o00_s00 Camera used:...

Then just re-insert the 4 screws that hold the mount and reattach the front panel of the camera. I have also included a 12mm tripod thumb screw for convenience. Print Settings Printer Brand: Creality Printer: Ender 3 Rafts: No Supports: No...

These provided a very good air seal, but left a lot to be desired.The fittings bite into the ptfe and stay attached a bit too secureThe metal fittings and couplers are heavy and wasteful for the number of caps I neededCutting the couplings in half...

... x4, 4 washers x8, a 6x2 barrier strip (optional). This design was made to fit on a Tarantula with the standard bed, one piece at a time. When printing, simply rotate each piece until it is flat against the bed. ...No supports will be necessary.

&nbsp;If you aren't going to use an LED light strip, you probably don't need the pins.&nbsp;100HexLightHolder_Diffuser.stl - This is to diffuse the LED lights, this should be printed in white or natural color...

Instructions and detailed specifications are still being developed for a version that can be printed on a Monoprice Select Mini stock and assembled into a full adapter. Formerly known as a remix, this design has been remodeled to take a MK2B heater...

You'll need to print 1 of each wheel, 2 of the stands. 8 of the risers. 12 of the spacers. 16 - 3x10x4 mm bearings needed. 2 - 3x100mm rods needed. (I used 2.9mm rods so easy to slide bearings and spacers on. 100 - 3x3x3mm Magnet cylinders...