naza remote led 3d models
91590 3d models found related to naza remote led.thingiverse
DJI Naza Remote LED mounting clip for SK450 Quadrocopter
thingiverse
Tired of constantly trying to adjust your remote LED so you can actually SEE it? I was too, and that’s why I made this simple mount that zip ties to your multicopter’s arm. You can easily twist this so you can see it from the top when working on...
thingiverse
... Instructions Print at .2mm with 3 shells. (Infill 8-15% not much needed) I put a piece of electrical tape on my frame where I stuck this, makes it nice and snug fit & use double stick to adhere your led to it.
cults3d
I just took michiwend's design and angled it for easier viewing below.
thingiverse
Needed some more space so added a small bracket to be able to place my sensor. Hope it's usefull for anyone! Instructions I printed at 0.20mm, used 225 degrees celsius and 10% infill. ...Printed on a...
thingiverse
Simply cable tie the clip to an undercarriage leg. ...It's a tight interference it and will not come out during flight.
thingiverse
Support Led NAZA pour fixation sur pied Tarot 680, percer deux troues de 2.5 mm ecartement 9 mm vis tete fraisee, Led a coller avec adhesif double face. ...(ABS)
thingiverse
The NAZA LED is pretty directional and has no mounting provisions.This part addresses both issues. Has to be printed with transparent material (obviously). ...The LED module fits in tightly so no glue is needed and it can be dissembled easily.
thingiverse
This LED holder fits between the top and bottom plates of your F450 or F550 frame. ...The LED is double side taped int the mount allowing you see it from the rear of the craft
thingiverse
Lightweight but sturdy holder for the LED module of NAZA-M V2 Flight Controller System (should be the same for the Naza Lite version). Fits snugly around a Dji Flamewheel arm with tie-wrap holes to hold it securely to the frame. It's a pretty...
thingiverse
Naza Led module mount for F450 frame. ...Compatible with both original flamewheel kit or third part kit.
thingiverse
What it says on the tin, 45 degree snap fit mounting support for Naza multirotor flight controller status led.
thingiverse
These are three parts to mount the NAZA V2 Led-Modul behind a wall part. I'am glued this parts together to use it. Led-Modul holder behind and Led cover in front of the wall.As Led opticical glass i'am cut the wires of a clear led (5mm) and put it...
thingiverse
Here is a mount for your Naza GPS and LED indicator. I used the same method as my gimbal mount. M3 push-in brass inserts and M3 x 12 screws to mount the GPS plate then stick the puck on with the 3M VBH. The LED mount is a tight fit but should...
thingiverse
Just a simple LED remote holder. Uses 2 flat head screws to mount. ...I used no supports and it worked out fine.
cults3d
A mount for antenna (x8r) and a naza led holder for fy680
thingiverse
A mount for antenna (x8r) and a naza led holder for fy680
thingiverse
Support to put the DJI Naza-H LED on the Align T-rex 450 SE V2
thingiverse
I've designed a Mount for the Status-LED of the DJI Naza M Flightcontroller. It is designed to mount your LED at the back of your aircraft facing in a nice angle down to you for maximum visibility. ...It can be attached with some 3M Tape wich is...
thingiverse
This is a mount designed to secure the LED for the DJI Naza M V2 Flight Controller. This allows the LED to be mounted in the upright position. The mount locates between the upper and lower plates of the multi rotor. Needed some minor filing...
thingiverse
Simple part that allows to clip the Naza V2 Led in place and can be used to put in the Sky Hero Spy frame using a M3 Screw beetwen the frame. ... Instructions print rotated 90 degrees in ABS at 0.1 layer...