naza remote led 3d models

Another simple remote control holder for people who want to pick up the remote and not use it in a mount.

I remixed this remote bracket to fit the bigger style IR Remote (reference picture). Believe thickness is the same. ... 2x 3mm screws

However, finally I grabbed the loose wires that have been having wildly around my printer and set them up and everything worked but now I had a remote to control them just lying around. So I decided to design a holder for the remote that sits on the...

I've been itching to upgrade my FLSunQQ-S with LED's for months now, but I kept putting it off because I was dreading disassembling the printer base. However, I finally gathered up the loose wires that were scattered all over my desk and managed to...

Designed to fit a generic LED remote control that can be purchased from Amazon. https://www.amazon.com/dp/B010MG4XTA/ref=cm_sw_em_r_mt_dp_U_rQy2CbSZEQ38F Print Settings Printer Brand: Creality Printer: Ender 3 Rafts: No Supports: No Resolution:...

Can be attached using two small screws.The remote is part of an LED Controller set, which you can buy from AliExpress (link below).SupportIf you'd like to support me for the 3D models I distribute for free, you can use the following AliExpress...

Controller device for Paulmann LED lighting system

I needed something to hold my countless number of remotes so I sat down and designed it!

I made the part a bit larger than the remote so the remote drops in without effort. You can use regular PLA and it will be fine. I just happen to like the finish of the PLA+ I created this in Fusion 360 so feel free to change the dimensions if...

A wireless charging dock for your remote control is perfect for keeping it within easy reach and reducing clutter on your desk or countertop.

A place to stash the remote control is needed. ...A subtle incline is integrated into its design to enable effortless retrieval.

Three minimalist designs for remote control storage units. ...Various credit card formats, including standard issue cards, easily slide into these compact holders.

I modified a design found at https://www.thingiverse.com/thing:341259 by expanding its dimensions, ensuring the remote control fits securely without getting stuck. ...Initially, when printing the standard version, I encountered issues with the remote...

Simple card style remote holder or hanger for 55mm wide remote or less.   You don't need to let it finish printing if you don't need the full length.   See photos.   Print standing up no supports.   Brim or raft if you have bed...

I made the part a bit larger than the remote so the remote drops in without effort. You can use regular PLA and it will be fine. I just happen to like the finish of the PLA+ I created this in Fusion 360 so feel free to change the dimensions if...

Yet, if you jam the remote into the compartment too tightly, it can be quite tricky to remove - a double-edged sword, really. ... To avoid any issues, I'm advising myself to lightly sand the interior or slightly increase the print size by 1-2% before...

This holder is for remote control with this dimension:Length: 86mmWidth: 40mmThickness: 6,9mmSupports: yes   

I reworked a distant control bracket to match a larger style infrared remote control unit. ...I verified that the thickness remains consistent with the original part.\r\n\r\nTwo 3 millimeter screws

LED Remode Control Holder Just fix it with a double-sided adhesive tape

Device Mounting System for Compact InfraRed Transmitters Used with Color-Changing LED Strips.

Electronic devices feature two bright LED lights, two high-energy batteries, and intuitive control buttons.

... to store the remote. Print instructionsMay be very tight fit. Works great, but if you jam the remote in there tight it is hard to remove, good but also possibly bad. ...Sanding the inside or bumping up the print size by a percent or two is advised.

i've design magnetic case for my led curtain. ... use 6x3mm magnets supports- tree infil 40% bridge enable

A holder for LED lights which can be held up by the screw hole or by double sided tape.

Remote Wall Mount Organizer A convenient and space-saving solution for keeping your devices at arm's reach, the Remote Wall Mount Organizer allows you to easily place your device on the wall while maintaining access to its controls and ports. By...

As we were always searching for the remote, I made this thing so my son can always attach the remote to his vehicle after he has chosen the color he likes. Please see the picture for printing-orientation (I was a bit lazy to change it after...

This is a remix of https://www.thingiverse.com/thing:4786524 with these changes - Resized to fit a remote that is about 40mm wide (can fit from 39mm-41.5mm) - Reduced height to 40mm to save some material - Removed the cut-out letters to make it...

This sleek housing cradles a full-color remote control, measuring precisely 91 millimeters in length, 63 millimeters in width, and a slender 8 millimeters in height. Put to the test and proven to be a perfect fit! ... For optimal results, I strongly...

A sleek device designed specifically to cradle your LED strip controller, complete with an accessory that enables effortless mounting onto a bar or rail.

I installed LED strips on my computer, work surface, and three-dimensional printing device, then decided it made sense to find a spot for the controller.