negative holder 3d models
333924 3d models found related to negative holder.thingiverse
This is a rough draft of an Omega 5D Enlarger negative holder which is blank so you can create whatever cutout is needed. I plan to create customized versions for different films and will publish here when finished. I'm also still working on the thin...
thingiverse
The holder exactly fits the standard 35mm template that comes with the Epson V600 film (and negative) scanner. The holder has bands to block out the area between pictures and a small peg to align the negative strip. I designed this to solve a...
thingiverse
This holds 4 frame 35mm film negatives flat so they can be photographed with a camera. Can be customized for different film formats and different print materials. Print Settings Printer Brand: LulzBot ...
thingiverse
I didn't like the 35mm negative holder that came with the Wolverine F2D Titan Film to Digital Converter. ... So I created this for me to scan the negatives more easier and faster.
thingiverse
A simple 35mm negative holder for scanning negatives using a DSLR. The opening on one piece is larger than the other, that side faces the flash. It's to ensure the light hits the whole negative. I put tape to avoid scratching the negative, using...
thingiverse
... magnets and glued them in. You have to put your negative in the holder and put second half on it. Remember to glue magnets properly, so they can attract. 3 last photos, are the result of scanning negatives using this holder and my digital camera :D
thingiverse
Omega D2 Negative carrier. Modify parameters and generate any size from half frame up to 6x12cm. I didn't do a 4x5 since I already have that but you can easily modify if needed. Uncomment the section and "top" or "bottom" for the size you wish...
thingiverse
Customized version of https://www.thingiverse.com/thing:431624 Created with Customizer! ...https://www.thingiverse.com/apps/customizer/run?thing_id=431624
thingiverse
I took bradbroks design and "shrunk" it from 6x9 to 6x6. ... I really love the feed design and it seems to keep the film nice and flat.
thingiverse
Customized version of http://www.thingiverse.com/thing:172274 Created with Customizer! ...http://www.thingiverse.com/apps/customizer/run?thing_id=172274 Instructions Using the following options: bold = Yes text = CAPTAIN NEGATIVE canh = 125 raise = No
thingiverse
This is designed to hold three Beseler 23c negative carriers. ...It sits nicely against the frame at the back of the baseboard.
thingiverse
Two-piece platform for digitizing 120 film (6x6 format) with DSLR. I enlarge the holes slightly with a drill after printing. I also double-stick tape microfiber cloths to each half so that when assembled, the film is gently sandwiched between...
thingiverse
Customized version of https://www.thingiverse.com/thing:4856226 Created with Customizer! ...https://www.thingiverse.com/apps/customizer/run?thing_id=4856226
thingiverse
Two-piece platform for digitizing 120 film (6x7 format) with DSLR. I enlarge the holes slightly with a drill after printing. I also double-stick tape microfiber cloths to each half so that when assembled, the film is gently sandwiched between two...
thingiverse
Customized version of https://www.thingiverse.com/thing:4856226 Created with Customizer! ...https://www.thingiverse.com/apps/customizer/run?thing_id=4856226
myminifactory
This tool is used to hold the negative probe when reading voltages on motor control boards for the Athena2 3D printer. It could be modified to fit another printer setup. ...The model was created using FreeCAD.
prusaprinters
Nozzle 0.4mm or smaller, wall thickness is 0.4 mm in order to be able to fit <3 mm negativesOrient as shown in picture below(tree) support is likely needed to bridge the gap.
thingiverse
... newer version with 116 LED's) didn't exist, so I designed one in Fusion 360. ...It features a lid handle thanks to another design, as well as a cutout / mount for bradbrok's [excellent film negative holder](https://www.thingiverse.com/thing:4701462).
thingiverse
35mm film negative scanning holder / carrier. Film may be tight and you may need to run some paper through the slots to clear them following the print. Uses two 14 x 2.5mm o-rings. Source as needed. Could potentially use a slightly larger...
thingiverse
This is a tool holder for my Ryobi Jigsaw and should work for other Ryobi jigsaws. You need to print it vertically, not flat to give it some strength. I printed it vertically and on an angle just to get it to fit in my printer's build dimensions. 20...
thingiverse
Pretty simple breadboard holder for Gridfinity (5x2). ... I also included a version without the Gridfinity base plate, and a negative of the breadboard cut-out if anyone wants to use that. ...
thingiverse
A simple, easy-to-print, retro-style 35mm film holder for DSLR scanning or negative viewing. The included registration posts make it easy to align when gluing and assembling. Please post your make. Enjoy File "35mm_Film_Holder_NG.stl" has a 0.2mm...
thingiverse
low poly face as negative mold and pen holder
prusaprinters
Then without closing 3dbuilder, create a new design (file menu) or open your own design that you want to add a spool holder arm receptacle to. Once the shape that you want to stamp a spool holder arm receptacle (hole) into is in your design space,...
thingiverse
My other scanner (an Acer Scanwit) has a very dedicated interface in which you can scan exactly 6 negatives in a fixed holder. Creating a holder for 110 negatives for this scanner seemed impossible. I therefore decided to create a holder for the...
thingiverse
... The system I'm using is the [*Valoi* negative holder](https://www.valoi.co/products) which comes in both 35mm and 120 film sizes. I've provided a holder model for the *Valoi* that should fit both their 35mm and 120 version - but not their advancer.
thingiverse
First a disclaimer: I strongly recommend the EFH for film digitalization and I have no connections with Andrew Clifforth whatsoever except that I have bought one of his holders. This thing is just an add-on to be placed above the EFH to make life a...
thingiverse
... too easily, over-spooling, causing tangles. ... I edited the file to make the ends the same dimensions to fit into the holders nicely, but with no bearings, so your filament spool has some friction rolling across these axles which don't roll in use.
cults3d
Tool for mounting 16mm motion picture film in a photographic enlarger. Designed with flipbooks and zoetropes in mind. Involves both 3D printed and laser cut parts. You'll also need: 10 M3x10mm screws 8 M3 nuts 2 1/4"-20 x 2" screws (yes I have a...