nerf rival attachments 3d models

Adapter I made for an Airsoft M4 Stock which I tactically acquired from my friend to connect to a Nerf XX-700

replacement pump grip for Nerf Pathfinder bigger and grippier hardware: reuse existing screws prints without supports in orientations provided rail part screw holes covered by thin wall to improve print quality, must be drilled out post process.

Replacement battery catch for the Nerf Perses (the hook that holds the battery pack in) The original catch broke on my Perses, designed a replacement that's thicker. ... Category: Toy & Game Accessories

Spring Spacer for the Nerf Vision XXII-800 adds 5mm of extra compression (theoretical max) boosts FPS from an initial 85fps up to 100fps. ... -noted, that online reviews rated the default fps as 100, mine might have been a lemon; unclear what the...

Spring Spacer for the Nerf Vision blaster add 5mm extra compression boosted my fps from 85, to 100 (noted that in some reviews the Vision had a starting fps of 100, unclear if mine was a lemon) should be installed on top of the 'traffic cone' at the...

Spring Spacer for the Nerf Vision XXII-800 adds 5mm of extra compression (theoretical max) boosts FPS from an initial 85fps up to 100fps. -noted, that online reviews rated the default fps as 100, mine might have been a lemon; unclear what the...

First step is to carefully cutting off the above rails on your nerf-takedown (Figure 3).Next, utilize sandpaper to meticulously smooth out the respective areas.Lastly, employ adhesive to securely affix the printed model.The other parts of this mod, I...

... the blaster effectively and easily, so I created a foregrip to make that possible. ... This is for the Nerf Pathfinder, designed to reuse the screws from the original grip. ...Long screws go in the handle, short screws connect the grip to the primer.

Completed assembly will hold about an extra 200 foam balls.Extra materials needed:Super glue5mm diameter x 2mm thick neodymium magnets (4 required) for the door assembly.3 Nerf screws 10 mm long thread. ... I harvested mine from broken blasters or from...

The part is sized for 17/32" brass to slide in and be secured by adhesive for 50cal foam darts(dartzone/nerf standard). ... This mod is intended for the hop up tab to be removed and the part to be glued into the pilots barrel for a permanent change...

Put this 3d-printed part inside the stock, rival ball accepting, breach (you will need to remove the hop-up). Then button up the blaster as normal. This has 3 printed parts to it: Inline Frontend Inline Mag Barrel Shroud The inline mags may...

I crafted this to perfectly fit over a Nerf Khaos blaster. It precisely follows the curves of the shoulder rest and necessitates enlarging the hole on the rest to create a through hole for an M3 bolt. The M3 bolt is firmly secured on the mount itself...

If you have done so, you can chamfer the end of the pipe so that the front barrel can move forward normally!*** 你需要： 三根PVC水管 一根300mm长，外径32mm，内径28mm 两根280mm长，外径18mm，内径13.5mm 8颗M3*10mm内六角螺丝 1颗nerf螺丝（如果你的打印机够大，则不需要） 如果有问题请留言 You need: Three PVC water...

The part marked O is intended for use with the great Out of Darts slim profile hopper release and the part marked as N is designed for the original Nerf hopper release lever arm. The non-tapered side goes against the release mechanism. It will...

All credit goes to AgentOrin, who was inspired by a well-known Nerf modder on YouTube. I used Meshmixer to stitch together multiple shells that were giving Cura and Slic3r headaches. The hopper and lid were split into separate files to make placement...

replacement Trigger for the nerf Pathfinder blaster enlarged cam surface so it fires with a shorter pull print parts in orientation as provided finger pad snaps-on**, no glue needed. dimensional accuracy is critical though, especially the first...

replacement Trigger for the nerf Pathfinder blaster enlarged cam surface so it fires with a shorter pull print parts in orientation as provided finger pad snaps-on**, no glue needed. dimensional accuracy is critical though, especially the first...

This has ribs to lock it in place on your rail, can be tightened to your preference, and is compatible with the RIVAL rail I made previously: https://www.thingiverse.com/thing:5718239 and of course it should be compatible with the existing rails on...

Half sized magazine - looks and feels less awkward than the stock mag.Holds 6 foam ballsDual mag. ...attachment included

Plunger Head Shim for Nerf Kronos / Heracles (and possible other Kronos reshells) Place this shim on the plunger head underneath the O-ring for a tighter seal. Same concept as the oldschool teflon tape wrapping method to tighten seals; but more...

Plunger Head Shim for Nerf Kronos / Heracles (and possible other Kronos reshells) Place this shim on the plunger head underneath the O-ring for a tighter seal. Same concept as the oldschool teflon tape wrapping method to tighten seals; but more...

This wall mount utilizing the top front attachment rails for mounting.  I made them fit extremely snug so you will need to do some sanding to get the perfect amount of grip when sliding the guns on the mount. In addition, I made two octagon ball...

I used hot glue to attach the printed part to the blaster and superglue to attach the switch to the printed plate. The plate that is used to hold the rev switch in place can be discarded. ... Use the OOD Perses mod guide found here for a...

These replacement sights don't cause damage to the blaster and does not require the entire shell to be removed during assembly.Parts include a blank sight (to completely remove the barrel sight), a low profile iron sight and a less intrusive iron...

The elevated side has to point towards the inside since it prevents the wheels from rubbing the braces when turning.Use some silicone spray to make the arm and wheel bearings run super smooth (and remove any squeaking)In the original thing the rubber...

* Use some silicone spray to make the arm and wheel bearings run super smooth (and remove any squeaking) * In the original thing, the rubber bands are attached to the braces. For me, it worked much better to just leave them on the top bar (as seen in...

This is a scaled Nerf rival ammo ball. I would recommend printing in TPE so it squishes Properly when shot. ...works great for spring powered rival guns but it does not work for flywheel guns.

Dual-wielding attachments has never been easier, thanks to their snug fit and ultra-durable build, polished to perfection with a silky smooth acetone finish that strengthens their grip. The front rail is equipped with a precision-crafted ring-sight...

This is a part that slips onto attachment rails found on Nerf Rival blasters and converts it to accept Picatinny attachments. Most Picatinny rail attachments use a bolt passing between the grooves of the rail to help mechanically secure attachments...

Mount a 45-Degree Picatinny Rail directly onto your trusty Nerf Rival Blaster.