no tf card ender 3 pro 3d models

This is an adapter for the Ender 3 Pro Printer. Instead of using the ribbon cable adapter, this uses the attached Cablecc SD card adapter. If your TF card adapter spring is worn and does not hold the TF card in, this will actually fix that problem....

This is a remix of the No Hardware Mount by Yashrg https://www.thingiverse.com/thing:3165335 for use with https://www.thingiverse.com/thing:3147899 for webcams Also based on Dauler's Ender 3 Rail Camera Mount. 'Specifically, the Y axis slip on'...

A simple Micro SD card holder to be installed over a 2020 or 2040 aluminum profile. You can place it wherever you prefer and one unit can hold up to 6 cards. ... BoM: - 02 M3 x 8mm screws - 02 M3 T-nuts <b>or</b> - 02 M3 x 8mm screws - 02 M3...

SD Card holder mounts easily to the front of the Ender 3 Pro.

I noticed there were no SD card adapters for the Ender 3 Pro so this was created using Autodesk Inventor. Stock bolts can be used to attach the plate. If you could leave a comment on how well it worked and/or you have any suggestions for the design I...

This is an SD Card Adapter / Holder for the Ender 3 Pro. This version uses the SD card adapter that comes with a small cable (7cm). There are two versions, with and without the box to store the SD cards. You can also print only the box. ... In...

so I am not a fan of tiny sd cards so I wanted to use full-size cards and so I searched Thingiverse and I did not see one for the Ender 3 Pro so I made one I used Cura for my slicer here is the reader I used https://amzn.to/2XeyotT

My computer came with an SD card reader and no MicroSD card reader and so it seemed to make sense to use an SD card reader for the Ender 3 and so I got a MicroSD to SD extender so it wasn't right under the bed of the printer. I printed this with...

The standard Ender 3 has the micro SD slot at the bottom rather than the top, so this is not an effective design for the standard unit.* If you prefer to use full size SD cards you can buy an adapter like [this one from...

There is so many similar microSD card holder for ender 3 pro printer. Want to make one with words at the front that is flushed with the front end of my ender 3 pro printer. For easier printing, I have split it into 2 parts (body and cap), which are...

There is so many similar microSD card holder for ender 3 pro printer. Want to make one with words at the front that is flushed with the front end of my ender 3 pro printer. For easier printing, I have split it into 2 parts (body and cap), which...

It all depends on the moment 😄 SD extension bracket and cable cover for Creality Ender 3 S1 pro 3D printer. Allows an SD card extension to be placed on the side of the machine with two slots for storing cards. Also a variant with a slot for the...

I wanted to use a full size SD card on my Ender 3 Pro. Unfortunately, every adapter I could find was oriented in a way that without twisting the ribbon cable, the card label would be facing away. This mount has room to twist the ribbon cable (try to...

SD card adapter holder for Ender 3 Pro. **Not suitable for Ender 3** (as the control board is flipped on the Pro). I didn't like the other holder I found here on Thingiverse so I created my own. It was designed for [this...

Clamping SD card holder

Remixed from a guard for Ender 3 Pro. This remix is for the original Ender 3. Since the design is a lot wider than the original, the right side is not secured very well, but the mod is still rigid enough that it stays in place neatly. I did not use...

This 3d model is a simple solution for all damaged sd card slots so it can be used to put the sd card in the correct place and re-print as good as before.

Holder for the creality original TF Cardadapter. ... An M3 bolt and railnut is required.

This is a remix of my Ender 3 SD Card and Micro SD card holder that allows the use of an extension cable and keeps the USB port available for use by Octoprint or flashing the firmware. ... I have not printed this model as I don't have an Ender 3 Pro,...

This is a remix of my Ender 3 SD Card and Micro SD card holder that allows the use of an extension cable and keeps the USB port available for use by Octoprint or flashing the firmware. ... I have not printed this model as I don't have an Ender 3 Pro,...

Ender 3 Pro display rear cover with SD card adaptor

A mod of "Ender 3 Pro Rail cover MOD" by Skorm3d (Thingiverse). ... I delete text.

This is an exact remix of Fanless PSU cover for Ender 3 PRO no noise but I removed the logo from the bottom if that's not your thing.

Drawer made by n6sxb remixed for Ender 3 (NO pro) with separator customizable. NOTE: This accessory NOT fit for Eder 3 pro version! for any suggestion write a comment for the drawer the support are necessary. UPDATE: 23/12/2019: Added...

This is a remix of 'Ender 3 V2 / Pro motherboard cover for 80X25mm fan (no support) by scaryPug (https://www.thingiverse.com/thing:4653994) I really liked scaryPug's design but wanted to fit a 92x25mm fan so I remixed it to fit one. Does fit on an...

The World's 1st print of Eiffel Tower with no support on Ender 3. ...

Storage for 3 SD cards on the profile of the Creality Ender 3 Pro.

A cover for Ender 3 for Bigtreetech TF_Cloud

This is a low profile fan cover that clips onto the stock Ender 3 Pro Fan. ...I designed this part to keep a low profile while also being convenient to print in under 2 Hours depending on your settings.

Ender 3/Pro Side Spool Mount - No extra hardware required. Simply drop the T-nuts into the slots (I suggest putting them in the wrong way round to spread the compressive load over a slightly larger area), then tighten the screws lightly. This...