noctua fan ender 3 3d models

A housing for a Noctua 40x20mm hotend fan, designed to work with original mounting holes and blower fan on Ender 3/Ender 3 Pro.

The case is based on the Ender 3 v2 version, but with the Noctua design in the center, showing the actual modification. When the project is ready it can be used to cover the original noctua fan with a personalized protection. ... This project is...

FRANÇAIS : Support pour ventilateur Noctua 60X25, afin remplacer celui d'origine de l'alimentation de l'Ender 3 V2. ... Nécessaire pour les modifications : - une Dremel pour découper la tôle ( et optionnellement les vis ) - une perceuse pour...

Required : a Dremel to cut the square hole a drill to make the four M4 holes a soldering iron x4 screws BHC or CHC M4x30 (Mesure the exact length and cut the end for a better finished before to screw the fan) x4 scews BHC M4x6 I am not...

Fan Noctura Direct drive

This is a cover for a Noctua 60x25mm fan, intended for use with the "slim" version of the Ender 3 Pro PSU. The cover allows you to externally mount the fan without needing to print an entirely new cover for it. ...

On Petsfang 5015 fans were too loud. ...So i redesigned the Fan Duct.

This is an Electronics front enclosure for Ender 3/Ender 3 Pro, it is designed to fit: - Bigtreetech SKR 1.4/1.4 Turbo - Rasperry Pi 2/3 - 4x LM2596 - 1x Noctua Fan 40x40 The design has been splitted in 4 parts, use selftapping screws 2.5 x 15 mm to...

This is an Electronics front enclosure for Ender 3/Ender 3 Pro, it is designed to fit: Bigtreetech E3 Mini Rasperry Pi 2/3 4x LM2596 1x Noctua Fan 40x40 The design has been splitted in 4 parts, use selftapping screws 2.5 x 15 mm to join the parts and...

This is an Electronics front enclosure for Ender 3/Ender 3 Pro, it is designed to fit: Bigtreetech SKR 1.4/1.4 Turbo Rasperry Pi 2/3 4x LM2596 1x Noctua Fan 40x40 The design has been splitted in 4 parts, use selftapping screws 2.5 x 15 mm to join...

This is an Electronics front enclosure for Ender 3/Ender 3 Pro, it is designed to fit: Bigtreetech E3 Mini Rasperry Pi 2/3 4x LM2596 1x Noctua Fan 40x40 The design has been splitted in 4 parts, use selftapping screws 2.5 x 15 mm to join the parts and...

This is my cover for the Noctua Fan upgrade. ... since the one i found didn´t fit my european version of the Ender 3 i decidet to make one by myself

This is a remix of scottyujan's PSU cover for a Noctua fan upgrade for the Ender 3 https://www.thingiverse.com/thing:4794712. There you will also find the cover for the fan. Check out his YouTube video on his upgrades for the Ender 3:...

This is a remix of scottyujan's PSU cover for a Noctua fan upgrade for the Ender 3 https://www.thingiverse.com/thing:4794712. There you will also find the cover for the fan. Check out his YouTube video on his upgrades for the Ender 3:...

Slapped this together in Solidworks since I couldn't find one for the Max version of the Ender 3. ...Would love to see some remixes of this as I have never made anything before and so believe this design could be greatly improved.

This is a Remix from https://www.thingiverse.com/thing:4794712 i made it to put a 80 mm Fan.

This is an Electronics front enclosure for Ender 3 V2, it is designed to fit: Bigtreetech SKR 2 Raspberry Pi Zero 2 1x Noctua Fan 92x10 Needs the feet extensions already installed. For specific to the parts I had available and the limited length...

This is an Electronics front enclosure for Ender 3 V2, it is designed to fit: Bigtreetech SKR 2 Raspberry Pi Zero 2 1x Noctua Fan 92x10 Needs the feet extensions already installed. For specific to the parts I had available and the limited length...

This power supply cover was created to contain a fan of the Noctua NF-A6x25 FLX. The Noctua fans are 25mm in height. For the assembly of the cover, n. ...6 plastic screws diameter 3 mm.

(https://www.reddit.com/r/ender3v2/comments/lto6uq/ender_3_v2_all_noctua_fans_buck_converter/) The PSU cover chilluniverse designed (https://www.thingiverse.com/thing:4567153) looks awesome! One issue, I had to print it sideways due to its...

Ender_3_v2_Silent_MB_with_LM2596S

Ender_3_v2_Silent_MB_with_LM2596S

This extruder lets you: - Use the Creality Ender 3 original heater - Fit a 20x20x10 mm fan on the heater - Fit a 20x20x10 mm fan on the part - Easy cabling - Easy mounting (using same holes) Print it using a 0.4 mm nozzle with 0.1 mm layer height. A...

To fix this I took a small file and just gave the screw holes of the fan a once over and with some mechanical retention (aka force) the fan fits perfectly without the use of screws (think of it as weight savings) If someone more talented than me...

https://www.thingiverse.com/thing:4441076 presented a thumb screw to replace the wing nut on the front-left corner of the BIBO bed. It is too wide for the other two positions. I have created a smaller version to fit the right-front corner and the...

Please note that if you go the route of using Noctua fans, they are 12V while Creality printers are 24V; hence, if you use Noctua, you must either: A) step the fan voltage down to 12 from 24V, or B) run the two fans in series rather than parallel. ...

Remix of Scott Yu-Jan's nice minimalistic PSU Shroud for a Noctua fan, but for the Non-Pro Ender 3. The fan cover fits a 60x25mm fan, and a Scott (as well as myself) used an NF-A6x25 PWM fan. ...Check his video for a specific link EDIT: Removed the...

... all the parts I had made for my hot end. ... It houses a 4020 noctua fan for the hot end, a 4010 noctua fan for part cooling, design incorporates the bracket and duct. ...Also includes a BL touch mount too which can be easily edited out if not needed

Allso i have 3 noctua fans in my previous setup to make it less noisy. The most parts i have found have, or the noctua fans, or the bltouch, but never both. And if they do, they rise a lot (in my mind that is) above the hotend-mount. With this...