nodemcu esp32 3d models

Rhasspy Dot Case for Matrix Voice ESP32 and Speakers Slim modular offline voice assistant case Assemby: print all parts glue the fabric to the cover - i used superglue cut the fabric leftovers from the cover mount the matrix voice hat with 2 small...

Window mount for your ESP32-CAM board Mounted with double-stick tape directly to the window make it possible to stick inside to show the outside with minimal reflections. The mount tilts the camera upwards and not straight forward. Used as a...

This nano data center is based on a Wemos D1 min ESP32 and has a 24 neopixel ring integrated (for optical alarms etc.) and a SPI port, for external connection of a nRF24 or LoRa module, is provided. All parts stick together and hold. No glue or...

Things Needed: Ai-thinker ESP32 cam 16 Led Neopixel Ring M3 Screws (5mm) M3 threaded inserts OD- 4mm (Optional) 3.5mm DC male/ female connector 5V Power Supply (Can use buck converter to lower the voltage of printer power supply from 24v to 5v)...

Required Components: - Wrover ESP32-CAM module - Two nuts M5 - Four screws with 60° heads, M3x16 (directly screwed into plastic) For optimal firmware performance on this module, refer to the GitHub repository at...

Case Enclosure for ESP32 Camera This compact case provides a secure fit for your ESP32 camera module. The durable plastic construction protects the camera from accidental bumps and scratches, ensuring it remains fully functional at all times. A...

This housing is intended for outdoor use of the ESP32-Cam microcontroller. There are fixtures for 5mm LEDs. I use infrared LEDs, so the camera can be used in the dark without visible light. But this requires a small modification of the ESP32 cam...

ThermIQ (www.thermiq.net) interface card för Thermia heatpumps, enables support for use via home assistant HASS, This is a case for the ThermiQ-ROOM2 i got delivered in early 2022, note that deliverys later in 2022 is built with addon boards ( so...

Compact enclosure for the ubiquitous ESP32-CAM with the USB-Serial board and an external antenna. The program- and reset-button are still accessible through the cooling slits. Update: SD-Card also accesible now! The holes in the bottom piece...

This is a customized version of some esp32 cam boxes that I found because the module I got seemed not to be the size of others as well as a different position of the led (or the other designs are wrong in size). I wanted to make a version as compact...

External Antenna Version of ESP32 WROOM Module The ESP32 WROOM module is a highly integrated Wi-Fi and Bluetooth wireless communication solution that provides an easy-to-use interface for various applications, including IoT, robotics, and more. The...

A 3D printed ‘box’, designed as separate box sides that bolt/screw together, to not only make printing easier, but also to allow the sensor and ESP32 components to be easily assembled inside the ‘box’.The ‘bolting together’ is accomplished by...

Small case for my NodeMCU incl. ...MH-Z19 Sensor

NodeMCU case with lid, DS18B20 doesn't contact with model.

NodeMCU case with lid, DS18B20 doesn't contact with model.

They difuse the ESP32 T8 leds, I used a 3d pen and translucent PLA as you can see in one of the photos. Check https://github.com/eried/pidflight-lap-firmware for more details. Parts ESP32 TTGO T8 https://s.click.aliexpress.com/e/\_d6sfNUb RX5808...

I've made this box for wallmount for a combined esp32 cam (blank camera is also shown on the picture). Not sure if all of these sold are within the same measurement, so I uploaded the fusion360 file. All parts/bodies are seperated by 0.1mm in this...

I have built an ESP32 radio (https://github.com/Edzelf/ESP32-Radio) on a 70x50mm perfboard. The following key-components were used: Speakers https://www.aliexpress.com/item/4000127737256.html?spm=a2g0s.9042311.0.0.22f54c4devAQBT MP3 decoder VS1053B...

The download is only intended for private and personal printing.Here you can find my special Code adaption to use the flash LED while streaming to monitor my printer while printing in the dark: uniforx/esp32camX: This is my adaption of the default...

Again, I haven't found a suitable case for THIS specific ESP32 variant, so I had to make my own. IT is fairly simple, prints in ~1h (0.3 layer, 3 perimeters, 10% infill), has buttons integrated in top cover and GPIO headers accessible from bottom...

I have built an ESP32 radio (https://github.com/Edzelf/ESP32-Radio) on a 70x50mm perfboard. The following key-components were used: Speakers https://www.aliexpress.com/item/4000127737256.html?spm=a2g0s.9042311.0.0.22f54c4devAQBT MP3 decoder VS1053B...

This is design to work with a MG90S servo motor and the ESP32-Cam case designed by SolarGermany https://www.thingiverse.com/thing:3949787/makes Demo: https://youtu.be/v_A3rCVCbVE Print Settings Printer Brand: Creality Printer: Ender 3 Rafts: No...

This cube box was specifically designed for the ESP32-EVB board. I intentionally left the buttons unattached from the top object, making it easy to add them separately as needed. My main intention behind creating this model was to control my AC using...

OnStep ESP32 mini telescope goto controller on base Howard Dutton project Key properties: The PCB has the same dimensions as the MiniPCB2 Big USB B port Bluetooth Wi-Fi Internal real time clock and PPS with battery backup Port for polar scope...

... SD card slot is now part of the lid print. I also slightly reduced and moved the camera hole to better match the ESP32 camera pieces that I have. ...The overall fit is far superior now, and using a 2 pin DuPont connector for power works well for me.

... from ebay. esp32-cam AI thinker 2n2222 npn with a 1k resistor for amplifications of the PWM I found on youtube. The printed one on picture with the circuit is a first version. ... https://github.com/moxl-420/ESP32cam-doorbell For full info

I like the simplicity of Carsten's ESP32 Cam Clamp and how it holds the camera in place. However, I wanted it to fully cover the front and use it with a <a href="https://www.aliexpress.com/item/1005003279204315.html">120 degree wide-angle lens</a>,...

I'm developing a custom case for the ESP32 Thing from Sparkfun, which has everything needed for development and testing of this popular module. As a first-time designer, there's still room for improvement: my current board lacks headers. I've set...

This is design to work with a the ESP32-Cam case designed by SolarGermany https://www.thingiverse.com/thing:3949787/makes Print Settings Printer Brand: Creality Printer: Ender 3 Rafts: No Supports: No Resolution: 200 Infill: 15 Filament: PolyMaker...

Using this clamp you can mount the camera module on a ESP32-Cam board in two orientations. For 90° rotation carefully fold the flex-print cable as shown and put some foam below the camera module, then snap the clamp on. Print Settings Printer Brand:...