nzxt h510 airflow mod 3d models
40375 3d models found related to nzxt h510 airflow mod.thingiverse
My GPU was suffocating inside my H510 Elite, so I created a front and side panel for better airflow. ...Air filters coming soon.
thingiverse
This is for a video. ...https://youtu.be/NaTBuYsSpjU Made for NZXT H510
thingiverse
Casefanholder 120mm for extra Fans on the bottom of your NZXT H510 Elite Case
thingiverse
shorter feet for the NZXT H510. may also fit H500 but can't confirm it. "ohne" version with flat bottom and one with indented bottom Print with support. ...(x/y dist ~0.8mm)
thingiverse
One of my H510's foot was broken so i remade it in a stronger version on the parts that broke. ... You need to keep the screw and the rubber pad that was installed with the old one, you can just glue it on the 3D print.
thingiverse
This is a wall mount for NZXT H510 Elite, but I think it will fit other NZXT cases to. ...Mount is 215 mm wide.
thingiverse
You need: - NZXT H1 - Deshrouded GPU, heatsink must not be taller than ~25mm (Distance from PCB top to heatsink top) (Gigabyte RTX 3070 Gaming OC works) - 2x GPU fan to regular fan adaptor cable (Aliexpress is your friend) - 2x Noctua NF-A15 - 8x M3...
myminifactory
It was designed for my specific setup but it should be able to fit into many rigs with minor adjustments to the height and foot, although I would recommend it particularly for use with the NZXT H510 Elite as the case has a cable managing bracket the...
thingiverse
Anti vibration mount for the NZXT H510 case. If you don't have these special screws that are shown in the pictures than print the files with the name _small_screw however I did not test those. the ending _46 and _35 refer to the diameter of the...
thingiverse
The reason for creating this is because I noticed that the NZXT H510 Elite has terrible airflow. I created this spacer to open the front panel slightly enough to increase airflow and not disturbed the aesthetic of a closed glass case. ...Enjoy.
thingiverse
just a mount designed with 3080ti for the NZXT H510
thingiverse
For the inside pieces I used 2 walls, 0 bottom and top layers 30% cubic subdivision for the pattern (pick whatever you like) I did the hole with the grinder and its dimensions are 160x300mm
thingiverse
a support for my vertically mounted Gigabyte RTX 3080 OC, which is mounted using a cooler master V2 universal vertical GPU bracket, the holes slot into the base of the case like lego.
cults3d
a support for my vertically mounted Gigabyte RTX 3080 OC, which is mounted using a cooler master V2 universal vertical GPU bracket, the holes slot into the base of the case like lego.
thingiverse
Headphone holder for NZXT H510 Elite housing. Trial and error is not for the professional model. ... 15-30% filling for PLA can be used.
thingiverse
A two-part headphones/headset holder designed around the NZXT H510 PC case, although this part will work with similar cases that have 25 mm tall feet. Only requires one 20 mm countersunk magnet, unlike my other design. The holder tucks under the...
prusaprinters
A two-part headphones/headset holder designed around the NZXT H510 PC case, although this part will work with similar cases that have 25 mm tall feet.Only requires one 20 mm countersunk magnet, unlike my other design. The holder tucks under the case...
thingiverse
This is a hard drive mount for an my NZXT H500. It was intended to reduce vibration and noise of my hard drive, but didn't work out so well for that. Uploaded anyway. ...Perhaps someone can use it.
thingiverse
Still experimenting with this mod, but basically it adds a small gap near the top. I had my GPU arranged vertically, and the fans were almost touching the glass panel. Looking at temps, they went up to 84-85C on my GPU after 5 minutes So adding...
thingiverse
***Updates*** - 2020-11-23 - added `nzxt-140-mesh-circle-v2.stl` new version with round holes matching original design ***NZXT back replacement*** Replacement for backpanel with mounting for 2 140mm fans ***Mounting ball*** This are for being able to...
thingiverse
A Remix of NZXT H1 lcd Panel for the 4 inch HDMI IPS Touchscreen 800 * 480 on Amazon LCD Panel https://www.amazon.de/Waveshare-4inch-LCD-HDMI-Resolution/dp/B07QK89X53?ref_=ast_sto_dp&th=1&psc=1 HDMI Cable...
thingiverse
This is a direct replacement for the factory front cover mount brackets, and adds another direction for airflow to enter from the base area, and exhausts more air through the top area. There is also a divider to prevent recirculation of exhaust air...
thingiverse
Wanted to give my PC case better airflow but couldn't find any designs I liked so I made something simple. This is the first model I've made so far and I'm pleased with the result. Lowered my Idle CPU temps by 5-10 degrees Celcius with an AIO. Cut...
thingiverse
This is a MOD for my case NZXT for better air flow. You can do the same if you like. You just need to cut the front panel for 38.5 x 14.5 and print the files. I have done all of this on my Ender 3, the Hoop had to divide by 3 to be able to...
thingiverse
This is a remix of https://www.thingiverse.com/thing:4883292 to allow it to fit in the front of NZXT H1. The pins are for the bottom of the 3d prints and will hold for the front. The new files have cut outs to fit. ...
thingiverse
Simple Cable cover similar to the NZXT cable covers but with the Corsair Airflow slices this has been made in two parts for easy printing and to allow long GPU cards the extensions screw in with M3 screws but be careful not to over tighten as they...
thingiverse
I use superglue to assemble ill add a picture so you can see where everything goes I use 10x1mm magnets I got on amazon and you can buy a mesh filter and cut it to size for some case filtration.
prusaprinters
However, the stock H17 is not a very good case in terms of airflow, and there are virtually no holes in the front panel.Without this mod, my 12500 reached around 95 degrees celsiusin the OCCT test, and was barely not thermal throttling. With the...
thingiverse
I was thinking how to improve the cooling of my old PS2 Fat/Phat , because i notice the airflow on the top part of the console (around the heat sinks) is kinda restricted so i made this simple "kit". ...I you gonna ask me why i did it why i cut a hole...