nzxt h510 elite front panel 3d models
152689 3d models found related to nzxt h510 elite front panel.thingiverse
The reason for creating this is because I noticed that the NZXT H510 Elite has terrible airflow. I created this spacer to open the front panel slightly enough to increase airflow and not disturbed the aesthetic of a closed glass case. ...Enjoy.
thingiverse
I use superglue to assemble ill add a picture so you can see where everything goes I use 10x1mm magnets I got on amazon and you can buy a mesh filter and cut it to size for some case filtration.
thingiverse
I had my GPU arranged vertically, and the fans were almost touching the glass panel. Looking at temps, they went up to 84-85C on my GPU after 5 minutes So adding this seems to drop the temp to around 80C I may try further distances to see how...
thingiverse
For the inside pieces I used 2 walls, 0 bottom and top layers 30% cubic subdivision for the pattern (pick whatever you like) I did the hole with the grinder and its dimensions are 160x300mm
thingiverse
This is a wall mount for NZXT H510 Elite, but I think it will fit other NZXT cases to. ...Mount is 215 mm wide.
myminifactory
It was designed for my specific setup but it should be able to fit into many rigs with minor adjustments to the height and foot, although I would recommend it particularly for use with the NZXT H510 Elite as the case has a cable managing bracket the...
thingiverse
My GPU was suffocating inside my H510 Elite, so I created a front and side panel for better airflow. ...Air filters coming soon.
thingiverse
Headphone holder for NZXT H510 Elite housing. Trial and error is not for the professional model. ... 15-30% filling for PLA can be used.
thingiverse
Panel is made from 9 main parts and "hardware" like pins and handles You will need 4 long and 4 short pins and couple handles (there are 14 holes but I haven't tested how many will be needed). It would be good to print samples of hardware to test...
thingiverse
This is a hard drive mount for an my NZXT H500. It was intended to reduce vibration and noise of my hard drive, but didn't work out so well for that. Uploaded anyway. ...Perhaps someone can use it.
thingiverse
Casefanholder 120mm for extra Fans on the bottom of your NZXT H510 Elite Case
thingiverse
This is for a video. ...https://youtu.be/NaTBuYsSpjU Made for NZXT H510
thingiverse
shorter feet for the NZXT H510. may also fit H500 but can't confirm it. "ohne" version with flat bottom and one with indented bottom Print with support. ...(x/y dist ~0.8mm)
thingiverse
PLEASE NOTE: This is a modification of one component from another project, therefore not a complete ready to be printed project. ...Visit this link to download the rest of the required components: https://www.thingiverse.com/thing:5213417 ...
thingiverse
One of my H510's foot was broken so i remade it in a stronger version on the parts that broke. ... You need to keep the screw and the rubber pad that was installed with the old one, you can just glue it on the 3D print.
thingiverse
Anti vibration mount for the NZXT H510 case. If you don't have these special screws that are shown in the pictures than print the files with the name _small_screw however I did not test those. the ending _46 and _35 refer to the diameter of the...
cults3d
As shown gpu support bracket to help stop video card sag
thingiverse
I ordered a custom front panel for the NZXT H210i from JakefaceCustoms on Etsy. https://www.etsy.com/shop/JakefaceCustoms Love the front cover, but the way it is designed and attaches, it leaves a gap at the top which kind of bothered me. ...So I...
prusaprinters
<p>The magnets used are 6mm X 1mm</p><p>Printed face down and superglue together</p><p>I have added the f3d,step and 3mf files</p><p>Hope it helps</p>
thingiverse
NZXT H7 Elite Front Panel Spacer ========================== This is a 2 parts Spacer for the NZXT H7 Elite computer case. You will be able to reuse the snapping part and the 2 screws from your NZXT case. It help drastically with the noise and the...
thingiverse
just a mount designed with 3080ti for the NZXT H510
thingiverse
a support for my vertically mounted Gigabyte RTX 3080 OC, which is mounted using a cooler master V2 universal vertical GPU bracket, the holes slot into the base of the case like lego.
cults3d
a support for my vertically mounted Gigabyte RTX 3080 OC, which is mounted using a cooler master V2 universal vertical GPU bracket, the holes slot into the base of the case like lego.
thingiverse
A two-part headphones/headset holder designed around the NZXT H510 PC case, although this part will work with similar cases that have 25 mm tall feet. Only requires one 20 mm countersunk magnet, unlike my other design. The holder tucks under the...
prusaprinters
A two-part headphones/headset holder designed around the NZXT H510 PC case, although this part will work with similar cases that have 25 mm tall feet.Only requires one 20 mm countersunk magnet, unlike my other design. The holder tucks under the case...
thingiverse
Designed up this dealer button to use in home games or have just as something laying around for any poker fan. It was inspired by a dealer button in Pokerstars VR. Printing: Ring - Infil to add weight, supports needed for spade inset. Letter...
thingiverse
Its sized to get above the motherboard in the HYTE Y60 case, but may be different depending on your motherboard, it goes past the motherboard on my system, but will mount closer to the front if thats a problem. ... Printed with no supports on its...
thingiverse
I liked the fronts of fractal design (meshify) cases but I own a NZXT H500 case. The front is all flat and has no ports for cooling so I designed a little piece to go on the front of the case to spice it up a bit! I added two files: one without...
thingiverse
Custom Elite Dangerous version of my [Corsair iCUE 4000X Front Panel design](https://www.thingiverse.com/thing:4889085) showing the 3 base Elite badges, Combat, Exploration and Trading (from top to bottom) This will fit the Corsair iCUE 4000X &...