nzxt h510 elite ssd mount 3d models
354341 3d models found related to nzxt h510 elite ssd mount.thingiverse
This is a wall mount for NZXT H510 Elite, but I think it will fit other NZXT cases to. ...Mount is 215 mm wide.
myminifactory
It was designed for my specific setup but it should be able to fit into many rigs with minor adjustments to the height and foot, although I would recommend it particularly for use with the NZXT H510 Elite as the case has a cable managing bracket the...
thingiverse
The reason for creating this is because I noticed that the NZXT H510 Elite has terrible airflow. I created this spacer to open the front panel slightly enough to increase airflow and not disturbed the aesthetic of a closed glass case. ...Enjoy.
thingiverse
My GPU was suffocating inside my H510 Elite, so I created a front and side panel for better airflow. ...Air filters coming soon.
thingiverse
Anti vibration mount for the NZXT H510 case. If you don't have these special screws that are shown in the pictures than print the files with the name _small_screw however I did not test those. the ending _46 and _35 refer to the diameter of the...
thingiverse
Headphone holder for NZXT H510 Elite housing. Trial and error is not for the professional model. ... 15-30% filling for PLA can be used.
cults3d
As shown gpu support bracket to help stop video card sag
thingiverse
This is a hard drive mount for an my NZXT H500. It was intended to reduce vibration and noise of my hard drive, but didn't work out so well for that. Uploaded anyway. ...Perhaps someone can use it.
thingiverse
just a mount designed with 3080ti for the NZXT H510
thingiverse
Casefanholder 120mm for extra Fans on the bottom of your NZXT H510 Elite Case
thingiverse
This is for a video. ...https://youtu.be/NaTBuYsSpjU Made for NZXT H510
thingiverse
shorter feet for the NZXT H510. may also fit H500 but can't confirm it. "ohne" version with flat bottom and one with indented bottom Print with support. ...(x/y dist ~0.8mm)
thingiverse
One of my H510's foot was broken so i remade it in a stronger version on the parts that broke. ... You need to keep the screw and the rubber pad that was installed with the old one, you can just glue it on the 3D print.
cults3d
a support for my vertically mounted Gigabyte RTX 3080 OC, which is mounted using a cooler master V2 universal vertical GPU bracket, the holes slot into the base of the case like lego.
thingiverse
a support for my vertically mounted Gigabyte RTX 3080 OC, which is mounted using a cooler master V2 universal vertical GPU bracket, the holes slot into the base of the case like lego.
thingiverse
I use superglue to assemble ill add a picture so you can see where everything goes I use 10x1mm magnets I got on amazon and you can buy a mesh filter and cut it to size for some case filtration.
thingiverse
this is a mount for the corsair commander controller. ...it is designed to fit the ssd mount in the nzxt H510i case.
thingiverse
this was a bracket i made in order to mount a 360 AIO to my S340 Elite
thingiverse
Still experimenting with this mod, but basically it adds a small gap near the top. I had my GPU arranged vertically, and the fans were almost touching the glass panel. Looking at temps, they went up to 84-85C on my GPU after 5 minutes So adding...
thingiverse
A simple replacement cover for a SSD/HDD in the NZXT case, giving a better finish while not having the all three drives mounted.
thingiverse
Moved the mounting hole up 6 mm, now it fits perfectly in my NZXT Case.
thingiverse
SSD Bracket to add more hard drives to a NZXT M59 Case. You will need to print x2 Brackets and 4 screws per SSD/HDD. ... The locking tabs don't quite lock in 100% but it fits perfectly and snugly fits a typical SSD/HDD in the bracket.
thingiverse
NZXT H7 Elite Front Panel Spacer ========================== This is a 2 parts Spacer for the NZXT H7 Elite computer case. You will be able to reuse the snapping part and the 2 screws from your NZXT case. It help drastically with the noise and the...
prusaprinters
SSD Bracket to add more hard drives to a NZXT M59 Case. ...You will need to print x2 Brackets and 4 screws per SSD/HDD. The locking tabs don't quite lock in 100% but it fits perfectly and snugly fits a typical SSD/HDD in the bracket. Print Settings...
thingiverse
SSD shroud Heat could be a concern. I've been printing them without a solid top and bottom layer, leaving just infill. ...I'm using cubic infill in the photos.
thingiverse
For the inside pieces I used 2 walls, 0 bottom and top layers 30% cubic subdivision for the pattern (pick whatever you like) I did the hole with the grinder and its dimensions are 160x300mm
thingiverse
A two-part headphones/headset holder designed around the NZXT H510 PC case, although this part will work with similar cases that have 25 mm tall feet. Only requires one 20 mm countersunk magnet, unlike my other design. The holder tucks under the...
prusaprinters
A two-part headphones/headset holder designed around the NZXT H510 PC case, although this part will work with similar cases that have 25 mm tall feet.Only requires one 20 mm countersunk magnet, unlike my other design. The holder tucks under the case...
thingiverse
Its sized to get above the motherboard in the HYTE Y60 case, but may be different depending on your motherboard, it goes past the motherboard on my system, but will mount closer to the front if thats a problem. ... Printed with no supports on its...