nzxt h510i hard drive bay 3d models
96539 3d models found related to nzxt h510i hard drive bay.thingiverse
This is/was a project of mine to keep drives that I'm doing data recovery on cool while they are running. ... It uses a 92mm PC fan to blow across the drives in hopes of keeping them cool enough to run data recoveries.
cults3d
This is/was a project of mine to keep drives that I'm doing data recovery on cool while they are running. ... It uses a 92mm PC fan to blow across the drives in hopes of keeping them cool enough to run data recoveries.
thingiverse
This a remix of the hard drive bay (https://www.thingiverse.com/thing:276524) where one can access all the holes unlike the original one.
thingiverse
... on eBay for 20$) and a 140mm fan in the back panel to cool the drives. ... To make the full assembly, you will need: 4x tray cage mirror -mid 4x tray cage -mid 16x drive tray At some point, I will make a spacer to allow the use of 2.5-inch drives. ...
thingiverse
NZXT H510i - Gap Filler for 120mm Front Fan Other parts may come later
pinshape
SummaryUse this to fit a 3.5" hard drive into a half-height (5.25" optical drive) bay. I used dimensions from the following two standards: 3.5" disk drive: SFF-8301: ftp://ftp.seagate.com/pub/sff/SFF-8301.PDF 5.25" optical drive SFF-8851:...
thingiverse
Use this to fit a 3.5" hard drive into a half-height (5.25" optical drive) bay. I used dimensions from the following two standards: 3.5" disk drive: SFF-8301: ftp://ftp.seagate.com/pub/sff/SFF-8301.PDF5.25" optical drive SFF-8851:...
thingiverse
This is a hard drive mount for an my NZXT H500. It was intended to reduce vibration and noise of my hard drive, but didn't work out so well for that. Uploaded anyway. ...Perhaps someone can use it.
thingiverse
Allows you to put the Vive connector box in an empty drive bay on a NZXT Switch case. The adapter is not perfect and I would probably do it differently if I were to redo it. It may work in other computers but I can't guarantee it will. ... Idea...
thingiverse
It was missing the hard drive bay cover and I figured I'd try to measure the gap with my calipers and print one. This works quite well. You may try elongating the little tab to make it more secure, but it works as-is. ... I'm going to deliver the...
thingiverse
Wanted something to hold my hard drives for my Open NAS. Its not pretty, but functional. Print with fan grill on the build plate, no supports required. Would love to know how to fix the "Object may not be a valid 2-mainfold" error. STL...
thingiverse
I bought a used AeroCool StrikeX open air case and it was missing one of the sliding hard drive mounts. I created this one to be as close to the original as I could make it with my printing capabilities at the time. As with all my items, it is...
thingiverse
Here is a expansion box that is created for adding 3 more hard drives internal in a computer case. Printed best with a 1- 1.6mm shell 100% infill is needed for good solid cage. ...also ABS or Nylon is best as the drives could warp PLA if you don't have...
prusaprinters
<p>I designed this model to fit in a HP Z240 full tower chassis. ...This will probably only work in computers with tool-less drive installation that is similar to the HP design.
cults3d
The adapters I designed allow the optical bay to hold two hard drives, and there is a clip-on bay that hangs below the optical bay that supports two more drives. ...Using these as well as the original mounts, this allows the case to support 8 total hard...
thingiverse
The adapters I designed allow the optical bay to hold two hard drives, and there is a clip-on bay that hangs below the optical bay that supports two more drives. Using these as well as the original mounts, this allows the case to support 8 total hard...
thingiverse
Dust Cover for Orico 4-bay hard drive dock. If you're like me, I only use the dock periodically and it can sit there for a while literally collecting dust. Made this to keep the exposed slots free from dust or even accidentally dropping something on...
thingiverse
8 bay rack for external hard drives. I am using it to hold and organize all of the drives I'm using for my raid array. I am sure I took it from elsewhere on thingiverse and modified it but I can't remember where I got it from. ... It is split into two...
thingiverse
... to build surface to help with the recessed screws. Mounts in standard drive bays and puts the wires as close to the original spot as I could get them. I got bored and just cut my lion out of the middle of it, works! ... Anyways, #Thank you!
prusaprinters
Replaces the CD drive and card reader and holds two 3.25-inch hard drives, but only the 19mm thick ones because, well that's what I needed the file for, and I didn't have enough room to work with 25mm ones anyway.But yeah, this is made for the 19mm...
thingiverse
With this fancypants bracket you can put a 120mm intake fan in your old ATX cases hard drive area. Try to think of a better idea first as this is a little silly. Oh yeah and my fan in the pictures was 38 mm thick. ...If you want a slimmer fan you need...
thingiverse
Remix of the double 5,25" bay PC computer to the external docking station for 3.5" HDD and SSD. Step file is temporary and not tested! Used on own risk. STL file is OK. No Raft and support needed . It is necessary to use the SATA Expander as it was...
thingiverse
Want to mount a 3.5" hard drive in a 5.25" Optical drive bay? https://youtu.be/U9krMN_wXHY This mount will accept a standard dell drive caddy, then slides directly into the 5.25" bay exactly like an optical drive. ...
thingiverse
Hard drive mount spacing is 10mm, so you can fit 13 7mm or 9mm drives, or you can fit 6 15mm drives, using every second mount... Or any combination of 7, 9 and 15mm drives. Space in the front is designed so you can fit two 70mm fans to keep the...
cults3d
Bracket to mount a 2.5" Hard Drive or an SSD Hard Drive into a 3.5" hard drive bay
thingiverse
Bracket to mount a 2.5" Hard Drive or an SSD Hard Drive into a 3.5" hard drive bay Instructions Mount Hard Drive into adaptor first.