octoprint psu control ender 3 3d models

Ability to use an Ender 3 board relocated to the power supply location on the Aquila.Old version is too tall (8mm total) and causes the motor drivers of the E3EZ to hit the top cover. ...New version (4mm total) should fix this issue.You can fit a 4010...

I made these legs for my Ender 3 v2. ... https://www.thingiverse.com/thing:4603075 I also made a fan cover for the Mainboard: https://www.thingiverse.com/thing:4612023 The fan I used was the Arctic F8: ...

This is a remix from https://www.thingiverse.com/thing:3023240 to fit the Ender 3 Pro/Meanwell power supply which has only one screw at the back. It uses the original screw (if you want to). No supports needed (if printed with 0.2 layer height or...

To solve this problem, I was looking for a new fan to install inside the PSU but found an old 120mm PC fan and a mount for the original Ender3 PSU online (https://www.thingiverse.com/thing:3359622). However, the Ender3 Pro comes with a Mean Well PSU...

The two sections where the screws go in are quite thin, this is to make sure you have enough thread on the existing screws to install the cover (no need for new screws!). Check also my fan silencer for cpu/motherboard fan:...

Check also my fan silencer for cpu/motherboard fan: https://www.thingiverse.com/thing:4635170 and other Ender 3 upgrades https://www.thingiverse.com/timqui/collections/my-ender-3-essential-upgrades Please share your makes and send me your thoughts...

... making super pretty, but it works very well. I used the Prusa 2.3 slicer, with hot end temps of 200, and bed at 60. Screw holes may need a bit of trimming after printing. I can't guarantee this will fit on anything but the Ender 3 Power supply

Bolts that you will need: - 4 M5x16 to screw into 40x40 extrusions (aluminum is soft, you don't need to tap it), - 2 M4x10 for attaching psu to the holder (from the back), - 1 M4x6 for attaching psu to the holder (from the top), - rest can be reused...

This remix adapts the original design from https://www.thingiverse.com/thing:3023240 to match the Ender 3 Pro and Meanwell power supply, which features a single screw at its back. It utilizes the existing screw (if desired) for this purpose. No...

I created a custom design for use with the Ender-3's power supply fan, scaling it to meet specific needs. WARNING: The internal voltage of the power supply is lethal and must be treated with extreme caution. Users are strictly prohibited from...

Here is a quick design I came up with to hold all of the tools that come with the Ender 3 Pro along with a few extras I have, like scrapers and nozzles. It's not by any means fancy, but it is definitely functional. I used Overture PLA with a nozzle...

... but I had issues with the extrusions part, it was almost impossible for me to slide the mounts onto the frame. ...I decided it would work better without the full extruded parts so cut them down and left spurs that will support the PSU.

Looking for a mount to attach my PSU to the outside of my IKEA Lack enclosure, I found PatPatate's remix and decided to move the screw holes to one side to make it possible to mount it to one of the Lack's legs.

Case for the Power Supply Unit (PSU) designed to enable installation of a Sonoff Basic module for convenient switching of the printer's power on and off. ...The enclosure accommodates up to three DC-DC converters, allowing for additional components such...

Designed this enclosure you house your PSU supply against a wall or similar structure if removed from your machine. I test fit a previous model that fit close to i adjusted the size but yet to physically test this new version. ... flip onto the top...

... installing this mod, and I will not be held liable. July 10, 2020 - The top mounting holes have been removed. - A Fusion360 file has been added for use. July 9, 2020 - A PSU cover with mounts for any 120mm fan using stock screws has been created.

... Inlet. ...Also usable without mounting on the Frame. Using a Noctua 60x60x20 Fan Silent and "cool" Design - the "loudest" Fan now is the Noctua 40x40x10 from the Extruder. Please open the PSU only if you know what are you doing! ...

I'm designing a new PSU cover that allows me to integrate a LM2596S module directly into it, which I plan to use in place of the original power supply fan. ...Specifically, I'm looking at installing a 120mm fan that operates on 12 volts, as suggested by...

This is an updated version of https://www.thingiverse.com/thing:3349588, tailored specifically for use with this PSU cover: https://www.thingiverse.com/thing:3515458. I've uploaded it here to make it easily discoverable by others. ...The design has been...

The system utilizes the built-in power supply unit (PSU) fan to effectively cool the Raspberry CPU, all while expertly positioning the camera at an optimal angle. ...To get started with this setup, you'll need a 30cm cable camera that can be easily...

A sleek solution to minimize noise from your power supply. ...It's a compact addition that not only reduces hum but also adds a touch of style to your setup. Simply attach it to the PSU with ease and enjoy a quieter computing experience.

While building an enclosure for my Ender 3 Pro, I needed a secure way of mounting my power supply to the underside of the cabinet. This was my solution. ...It secures the back and middle of the power supply, with enough clearance for the factory...

A simple remix of the front part, it was too wobbly to me so I designed these two holes. The t-nuts and the bolts used are spares i got with the printer, so you should have these two. Print Settings Printer Brand: Creality Printer: Ender 3Rafts: No...

Something I made to replace the stock fan on the Ender 3's power supply. The 92mm fan is the largest I was able to fit on the power supply. The fan I use is this one:...

2 Extra wire holes on back, the bigger one lines up with v slot on the rail the psu connects to so you can run a wire to the top for an LED bar. Use M4x8 screw for door handle. screw in a couple turns to lock it. ... Switch model has 20x13mm...

This remix is ​​useful for mounting your PSU on the back without the need for an angled cable. I started from an already created base and I modified some parts of it. There are some errors here and there, small cosmetic defects and missing the...

Before print check on which side you have you have fan on psu this is possible you should reverse this on your Slicer. ... Thanks for: https://www.thingiverse.com/abrenoch/designs I used this 60x60 mounting bracket: https://www ...

Moves plug and switch to back and has a slide off door to easily access the wiring.2 Extra wire holes on back, the bigger one lines up with v slot on the rail the psu connects to so you can run a wire to the top for an LED bar.Use M4x8 screw for door...

With this expertly crafted Double Z PSU mount, you'll enjoy enhanced performance, increased durability, and unparalleled peace of mind. ...Whether you're building a high-end gaming rig or upgrading an existing system, this innovative design is sure to...

The fifth hole is used to make a ground connection which was eliminated when the PSU was relocated. For the ground, I used a wire connected to the AC ground wire in the wiring box and attached a screw lug to the free end. I then used a T nut and an...