octoprint psu control ender 3 3d models
847069 3d models found related to octoprint psu control ender 3.thingiverse
-------------------------------------------------------------------------------------------------------------- In adapting the Ender 3 to make use of the Octoprint "PSU Control" plugin my goal was to not permanently butcher the machine in any way. ...
thingiverse
### 5V PSU : I used [this 5V PSU](https://fr.aliexpress.com/item/33012749903.html?spm=a2g0o.order_list.0.0.21ef5e5bbqTvpt&gatewayAdapt=glo2fra)(5V 2000mA) to power my raspberry running Octoprint. **I do not recommend this PSU, It make a light but...
prusaprinters
SummaryHere is my custom PSU mount for my Ender 3 Pro.It has a few features and advantages compared to the stock PSU mount :Low profile mount : nicer look and lower the center of gravity so more stabilityRelay : mount for a relay, used to power on...
thingiverse
*Note: This is designed for the stock PSU on the original Ender 3, and not the slimmer Mean Well PSU on the Ender 3 Pro.* **Printing** This is designed to be printed with out supports. See the photo of the completed print for the correct orientation...
thingiverse
... und mit dem Slicer in die Öffnungen des Deckels gemacht. ... Die Cam-Halterung habe ich von https://www.thingiverse.com/thing:3147295 Unter https://technikmensch.de/octoprint/ habe ich eine super Anleitung gefunden. ...
thingiverse
I'm using the Octoprint-Enclosure plug in to trigger some GCODE for each button. As buttons, I used some generic 24mm "arcade buttons" found on amazon. I use the top 6 buttons to perform routine actions, homing, set temperatures, filament...
thingiverse
This is a 3-part case designed to mount a Raspberry Pi 3B+ to a Creality Ender 3 using M3 machine screws and t-nuts. Mounting points in the center part allow for the installation of a small 5V fan for cooling the pi during use. This fan may be...
thingiverse
Wanted to mount this in front of the control board. Used 2 - M3x10mm screws. This is a remix from https://www.thingiverse.com/thing:4567163 ********* Updated Jan. 28, 2021 ********* Found that the original version was very flimsy so I...
thingiverse
This design adds a case to your Ender 3 (Pro) that fits a Raspberry Pi 3 Model A+, a 10A relay (for switching LEDs on/off), a 30A relay (for switching printer on/off), a buck converter (for powering the Raspberry Pi from the Ender 3's PSU) and a...
thingiverse
This design is a remix of my [Raspberry Pi 3 Model A+ case](https://www.thingiverse.com/thing:3338152) for the Raspberry Pi Model B+: It adds a case to your Ender 3 (Pro) that fits a Raspberry Pi 3 Model B+, a 10A relay (for switching LEDs on/off),...
thingiverse
AiO Ender 3 Octoprint Set Up ================= Features: ------------ - Easy to set up. - Printer on/off remote switch. - Light on/off remote switch. - Switches work with Octoprint telegram plugin. - NO CABLE MESS under the printer. -...
thingiverse
OctoPrint supports Power Supply (PSU) management with the "PSU Control" plugin. This box is for the [HiLetgo 5V 1 Channel Relay Module with optocoupler Support High or Low Level Trigger](https://www.amazon.com/gp/product/B00LW15A4W) which, I...
thingiverse
Remixed from giacomo30196's wonderful [Ender 3 Octoprint Set Up](https://www.thingiverse.com/thing:3063845) box. This version will fit an Ender 3 Pro and hold larger FC-65 high-amp relays and larger LM2596 voltage regulator with LCD display, in...
cults3d
Remixed from giacomo30196's wonderful Ender 3 Octoprint Set Up (https://www.thingiverse.com/thing:3063845) box. This version will fit an Ender 3 Pro and hold larger FC-65 high-amp relays and larger LM2596 voltage regulator with LCD display, in...
thingiverse
Antenna mount goes into the Enders case cover hole that initialy was made for Z endstop cable. Dmall thingie C6 that is for saving the camera cable from skew. It should be pressed in the hole where camera ribon slides into the camera box. OPI...
prusaprinters
The cover portion fits nicely within the frame and can be removed whenever you want to.This is a remix of “Octoprint Monitor Single Station Front Cover” by Bazzelworks found at this link Octoprint Monitor Single Station Front Cover by...
thingiverse
I've remade this to fit the Ender 3 Max as it is made differently and the original one just doesn't fit it. This is made to slot into the 4020 section ad located behind the installed LCD screen. ...and hole for 40mm fan is in the side to allow air...
thingiverse
I have my Raspberry Pi and Arduino-Uno powered from the 12v PSU, so I made this cover for the Ender 3 (Cheap Chinese PSU) so that the 24v and 12v PSU can fit into one enclosure. I also didn't like the add on fan silencer for the Ender 3 PSU, so this...
thingiverse
This is an Ender 3 vent that fits perfectly well with any stock Ender 3 PSU.
thingiverse
Ender 3 PSU support with enough space to run some cables through. ... Uses OEM screws.
thingiverse
PSU mount for the original Ender 3 PSU. I had to relocate the PSU because of the dual Z stepper. I didn't like the existing mounts, so I designed my own. ...With this design the PSU will be mounted next to the Ender frame (outside)
thingiverse
This is a front plate for the ender 3 PSU, the fan cover from the original design works for this one as well.
thingiverse
... I could fit a second z-screw.. ...so, I made this. A replacement PSU cover for the Ender 3 - beefed up for strength, allowing the PSU to be moved further back and mounted vertically bolted to the rear extrusion. ... Use with m4 screws and t-nuts
thingiverse
This model is based on the original PSU cover that comes with the Creality Ender-3. I'm planning to relocate the PSU as well as the relative location of the switch/fuse/power connector assembly, so I needed a digital copy to start from. Keep in...
thingiverse
There are some feet for Creality Ender 3 PSU for standalone. You have to print X2 for each side (better). ... Thanks for your support many things are coming soon :)
thingiverse
Larger cover for ender 3 PSU with 2 spaces for switches, connector may be attached using M3 threaded inserts, on the back it has a hole to pass throught the XT60 connector
thingiverse
When assembling the Ender 3 the bottom bolt holding the PSU in place stripped metal on the PSU, so it wobbled a bit, though I'd probably still have made this anyway. The shorter version is to work with this dual z axis modification:...