octoprint psu control ender 3 3d models

I designed a custom control knob for my Ender 3 because the original one drove me crazy!

It doesn't seem to slow the fan down, but I've put this project as "Work in progress" until I do some further testing on its effects on the fan's performance. Air duct cover for Ender 3 PSU (or any compatible power supply). Mostly for noise...

The bottom of the PSU is approx 1/4" off the surface when the stock rubber feet are used. I recommend using a different type of feet to raise the whole printer off the surface. You will need extra bolts and nuts to mount. Simply remove PSU from...

... Remove plastic housing from PSU. Remove 3 wires from switch and run thru small square hole in back of switch box. Reconnect wires and mount switch box. Mount left and right supports to PSU, using stock holes. Then mount to structure. ... Enjoy!!

Lightweight PSU silencer for Ender 3 (& possibly other Creality) printers. Fits for fans with diagonal distance between screws of 71,5 mm. All walls have just 1,2 mm. ...Additionally the outlet channels are wavy reducing noise even more. Print flat,...

I'd like to extend special thanks to Coillote and his Ender 3 design, which served as inspiration for my own creation. You can find his design here: https://www.thingiverse.com/thing:3044639 In the near future, I'll be adding a PSU cover to enhance...

This part is designed to mount the power supply for the Ender 3 Pro (Meanwell LRS-350-24) to a leg of an Ikea Lack table. The legs of the table are hollow, so you can drill a hole behind the mount to run cables through. Don't forget to ground the...

This part is designed to mount the power supply for the Ender 3 Pro (Meanwell LRS-350-24) to a leg of an Ikea Lack table. The legs of the table are hollow, so you can drill a hole behind the mount to run cables through. Don't forget to ground the...

A remix of another fantastic design for attaching a larger (quieter) fan to the Ender 3 V2's PSU. I didn't need as deep of a shroud, instead using an 80x15mm fan (one from Arctic Cooler). As I am printing this in my dorm room, and want to avoid...

________________________________________________________________________ __Update:__ __04 Jan 2021:__ + added a frame to mount the C3D 1.1.3 board and other bords with the same layout + touch upon the design -> better printable __07 Jan 2021:__ +...

This is a PSU enclosure designed specifically for the Ender-3 Pro's power supply unit. This innovative design boasts numerous capabilities and conveniences not found in the original model. 1. The power cord is neatly routed back into the case. 2. 3....

This thing needs to be printed vertically and rotated at a 45deg angle to fit on the Ender 3 bed. The fan grill is printable in the vertical orientation - don't put supports in it or you'll break it! Print with a raft and regular "supports...

This is an Ender 3 Control Knob. ...I suggest printing it upside down with supports only along the indent in the middle.

I upgraded my PSU fan with a larger and quieter one, that I mounted externally to the PSU case.

Protective cover for silencing and redirecting the ventilation of the power supply, created for an Ender 3

One side of the PSU's fuse plug isn't screwed into the PSU, which causes it to sag. ...This issue is resolved by securing the plug in place and adding extra support for the PSU.

Modular Upgrade Component facilitating the swap of a 120mm fan for the stock 60mm unit on the standard power supply of an Ender 3 Printer.

A compact fan silencer specifically designed to attach directly to the stock power supply unit of an Ender 3 Pro 3D printer.

Mod to remount your Ender 3 power supply. ... Requires: 4 x M4\*12 1 x M4\*8 1 x M3\*8 1 x M4 Nut

Adapter allowing to install a 120mm fan instead of the 60mm one on the original power supply of an Ender 3.

This is a control dial that allows for quicker rotation. ...It was modelled for my Ender 3 V2, so it may be applicable to other printers that may share the design of the stock dial. ...

ABS 100% infill should hold PSU with one bracket. ...Please consider the print orientation.

ABS 100% infill should hold PSU with one bracket. ...Please consider the print orientation.

As title says - simple mount for E3 PSU Can be put on wall with two screws.

And as I wanted to replace the old PSU with the LRS-350-24 PSU from Meanwell, this asked for a redesign (o;It is advisable to have a protective ground cable attached to the PSU and the back of the profile as the supplied mounting angle for the PSU...

Easy-to-use knob controller designed specifically for Ender 3 3D printers, featuring ergonomic knobs for precise rotation control. A small thumb-controlled knob adds flexibility to your printing experience. To assemble the controller, use a 4mm...

Lüfterlose Netzteilabdeckung mit Namensschild. ...Könnt ihr euch gern mit einem Namen benennen und dann Drucken. Läuft bei mir seit mehreren Wochen ohne Probleme. https://www.tinkercad.com/things/kPpW0TWw9dd Ender 3 - Großes Meanwell Netzteil

Unfortunately the original did not fit my Ender 3 so I remade it from scratch in fusion. ...If you find the original doesn't fit I hope this works as a backup.

Rapid PSU assistance, shaved off extra weight already. ...Revisiting it further can liberate a significant amount of unnecessary plastic usage.

The power switch will be moved up front near the control panel to be more accessible, where I think it should have been from the very start. :) Printing of this component is happening right now, with the left side estimated at about 5 hours,...