od tubing 3d models
82423 3d models found related to od tubing.thingiverse
Used to hold 6mm OD tubing from an aerator. Uses Command Strips to hold the mount to the wall, tank, or stand. ... Print VERTICAL for the best strength.
thingiverse
A corner for making boxes from 0.75" OD tubing. One version with ears for mounting side panels. The other version without Epoxy the tubing in. Made with Mathematica and OpenSCAD. ...
thingiverse
Just a basic, screw-on irrigation tubing clip for 6mm outer diameter tubing. File numbers represent how many tubes each model can accommodate. No supports needed, quick print. ... Apologies for the cringe pictures, been using these for years, just...
thingiverse
Just a basic, screw-on irrigation tubing clip for 6mm outer diameter tubing. File numbers represent how many tubes each model can accommodate. No supports needed, quick print. ... Apologies for the cringe pictures, been using these for years, just...
thingiverse
Small adapter to attach 7/16" OD flexible tubing to the Ryobi high volume cordless inflator. Tubing should slip right in the front, and I use a bit of CA glue to hold it in. ... Im sure tubing varies a bit, but this should be close.
thingiverse
This work is a part of my progress towards the Public Lab Reconfigurable Rig, work done as a part of my Autodesk Student Expert Internship at Public Lab. ... Check out the current Reconfigurable Rig files and instructions on Github.
thingiverse
It's set for 14mm OD tubing. Smaller should work just fine, though, and I'd imagine that 16mm OD would kinda work too. Worst case, scale it up by 5-8%, as the channel diameter is just a hair over 15mm, but I can't confirm if this will fit. ...
grabcad
This is a generic hose barb for 6mm metric tubing with M5x0.8 threads
thingiverse
......I was not able to find PC6-M10*1 pneumatic fittings, which would normally be used to fit 6mm tubing to the adapter vertigo235 designed, for a reasonable price. This is to give a similar push-to-connect interface for 6mm tubing as the pneumatic ones.
cults3d
......I was not able to find PC6-M10*1 pneumatic fittings, which would normally be used to fit 6mm tubing to the adapter vertigo235 designed, for a reasonable price. This is to give a similar push-to-connect interface for 6mm tubing as the pneumatic ones.
prusaprinters
An added bonus is that you can fit the tubes in one at a time instead of the juggling act of all at once like with the stock mmu. STL file is called "OD6mmTubeToMMU_Adapter.STL". ...I left the original part in the folder in case you want to continue my...
thingiverse
Modified [JOHNNYBOI's trumpet pencil clip](https://www.thingiverse.com/thing:1318176) so that it can hold onto the straight tubing that is around the main tuning slide of the trumpet. It has an **outer diameter** of **14mm** in my case. I set the...
thingiverse
Customized version of https://www.thingiverse.com/thing:454702 Created with Customizer! ...https://www.thingiverse.com/apps/customizer/run?thing_id=454702
thingiverse
Customized version of https://www.thingiverse.com/thing:2932635 Created with Customizer! ...https://www.thingiverse.com/apps/customizer/run?thing_id=2932635
thingiverse
This is a 120mm fan adapter to a 103mm OD tube / pipe (ID is 104mm so 1mm tolerance) Was designed to use on a server rack with a fan to guide hot air out using a pipe.
thingiverse
Connector to connect a 1" OD tube to a flat board with a slot for any internal wires to be routed out without pinching. Part of my thesis robot. ... Instructions ABS 230 C Heated Bed (blue tape) 110 C...
thingiverse
A simple adapter to connect a 10mm OD Tube to a Coke bottle. Prints without support. If you found this useful, please donate what you think it is worth to my paypal.me. Help cover the time of design. ... Thanks, Enjoy!
thingiverse
I have made a simple cap to cover the sharp ends of a 1" OD tube with 1.5mm walls. I designed these for my MPCNC. The design takes advantage of the burr left after tube has been cut by a pipe cutter and locks in place with the burr left inside. To...
thingiverse
Cap fits snugly on the end of 1/2" OD Vinyl Tubing. ... See also for 1/2" ID http://www.thingiverse.com/thing:382516
thingiverse
Clip for any tube with 16mm outer diameter. Recommended for 4mm tapered screws. ...8mm head size.
thingiverse
Customized version of https://www.thingiverse.com/thing:2932635 Created with Customizer! ...https://www.thingiverse.com/apps/customizer/run?thing_id=2932635
myminifactory
This is the type of coupling that I used: "4mm OD Tubing to 1/8" Male Thread - Quick Connect for Bowden Extruder Tubing" Update: I tweaked the opening for the push fit coupling, it now screws in perfectly straight off the printer, I also tapered the...
thingiverse
This is the type of coupling that I used: "4mm OD Tubing to 1/8" Male Thread - Quick Connect for Bowden Extruder Tubing" Update: I tweaked the opening for the push fit coupling, it now screws in perfectly straight off the printer, I also tapered the...
thingiverse
This is basically the same as the source for the remix, but with a little additional support for a larger diameter tube. ...I think it's about the largest inch-sized tube you can stick under a V6 block.
thingiverse
I've attempted to make it adapt to a ridgid shop vac hose, which I've measured at 57-58mm OD. ...I haven't ensured it will clear the handles of the plunge router base and whatnot, and some of the junctions between the different sections are a bit rough,...
thingiverse
Watch the print occur at http://youtu.be/7OoFe0CkZio Instructions The fitting sits on the edge of 1/8" glass, and was designed for 5/8" outer diameter (1/2" inner diameter) clear tubing. In the picture, the water comes up into the fitting the...
thingiverse
This is a remix of [RhinoAus](https://www.thingiverse.com/RhinoAus)' [Nerf Sledgefire Single Shell](https://www.thingiverse.com/thing:2291606), made to fit 9/16" OD tubing.
thingiverse
This is an endcap for a 26mm ID tube 28mm OD. I used it for a carbon fiber curling broom handle. ... But it could be used for anything.