olympus om 1 motor drive 3d models

This is a printable cap for the motor drive (winder) connection at the bottom of Olympus OM-1 and OM-2. (OM-3 and OM-4 use different screw-in cap). These cost $15 or more on eb*y, but if it's not for the shelf queen camera, this printed one will...

This will cover the motor winder port on an OM-1 (and possibly other OM verisons?), it's a pretty small print but mine fits nice nice and flush and turns in with just a bit of effort using a €0.05 coin.

Grip for Olympus OM-1, based on the OM-4 grip by @digduck (https://www.thingiverse.com/thing:2952837). ...I have not printed this yet, so I don't know how well it fits.

Copy of an old Olympus analogue camera. The knobs and lens need some support. UPDATE 12-3-2017: Added an easy print version in 2 pieces that doesn't need support (not tested yet so please give me feedback). ... Print Settings Supports: ...

I designed this version of the OM system Camera Grip 1 based on the original Camera Grip 1, which currently is extremely rare and thus quite expensive. I am fortunate enough to have two of them, and thought in creating this would allow others to...

... to the tripod mount. ...For Olymus OM-1 and OM-2 film cameras. ...With how I printed it, I printed a bushing to be glued into the 1/2" hole in the base to form the proper stack height for a 1/4" diameter machine screw that is approximately 1/2" long.

This is a dummy battery for Olympus cameras using the BLN-1. This includes the OM-D E-M5, E-M5ii, and E-M1, as well as the PEN E-P5. I don't know yet whether the new PEN F uses this battery, but I suspect it will. This will allow you to power your...

... stick with the photos at the end. ... That's when the Olympus camera model from 3DTestbench came in handy. I scaled the camera down a bit and added a cutout for a USB stick. The USB stick can simply be plugged into the side of the "USB port". ...

... The one in the photo is scaled 50% for an RC scale model. Will post pictures of it painted when done. Print Settings Printer: Anet A8 Supports: Yes Resolution: 0.1 Infill: 15% Notes: Lay the parts flat in your slicer software, lens pointing up.

I recently bought a pair of Olympus OM2n cameras, and one of them was missing its battery and motor drive body caps. I tried both models available on thingiverse (https://www.thingiverse.com/thing:4297605 &...

Good fit for canon EOS devices printed at 100% scale. ...allows you to fit lenses with with an Olympus OM mount to your canon EOS camera body.

An attachable diffuser for the pop-up flash on Olympus OM-D cameras. Can be attached or removed with the flash both up or down. ...Fits on OM-D E-M10 Mk.II but should work with other models as well.

Diffuser for the built-in pop-up flash on the Olympus OM-D cameras. Tested to work on OM-D E-M10 II, will probably fit other as well. Just slide it into the hot shoe and fire away. ...Can be taken on/off with flash either up or down.</p><p>Print with...

This was designed for an Olympus OM-D E-M10 Mk1. I don't see why it shouldn't be compatible with other OM-D cameras, but one commentor said it specifically does not fit the E-M10 Mk2. I don't know about any other models. ...The sketchup file is...

The Adapter to fit Tokina 135mm Lens with Om Olympus mount to my Sony A7 with E mount

This is an adapter to convert lenses that use olympus om mount to the sony e mount, it should be printed with the olympus mount facing the bed plate. ...

I lost the old hot shoe cover for my Olympus OM-D E-M10, so I edited the one from babr to fit my camera. It's pretty firm and fits nice, so I hope it won't fall out (unlike the original cover). ... It will probably fit the other OM-D cameras from...

Custom grip for OM-D camera (Olympus E-M5) Instructions Added a lip so grip doesn't turn. ... If you want to have access to battery without removing grip, you can cut this part using a sharp knife.

http://www.thingiverse.com/apps/customizer/run?thing_id=229961 Instructions Using the following options: height = 3 layer_height = 0.1 size = 100 image_file = fullyparametrizedlithopane20150218-3763-106venu-0.dat lithophane_border = 3 bottom_padding...

i made a c-mountable adapter base on this design https://www.thingiverse.com/thing:5495794 it has 46mm flange distance in respect to olympus OM lens to c-mount body if you want a macro just add 5mm extension c to cs mount spacer ring found here...

This is is a lens adapter to fit an Olympus OM-mount lens on a m4/3 camera. - Flange distance compensated for mft, it will focus to infinity. - A notch inside the barrel push the aperture preview detent to allow the aperture selector ring to...

Drog33 did a great job designing a grip for the OM-D E-M10, unfortunately it wasnt the greatest fit for my hands, I made it a bit larger and grippier, and added an internal space for a 1/4-20 nut so you can mount whatever you want to it. ...Just insert...

Dies ist ein Akku Dummy für einen Olympus BLS 50 Akku. ... Inspiriert von diesem Dummy https://www.thingiverse.com/thing:1308476 Aufbau ist analog zu diesem.

Spare part for OM Auto bellows slide element, this iteration suits best for me. ...I printed this few months ago and was testing, so don't remember print settings.

I made this to throw in my bag to keep my batteries for my OM-D. Fits 3 oem or generic batteries. I simplified it a bit from the rendering. Uses 2 m-3 bolts and maybe a washer if you want it a bit smoother sliding. ...Prints with a ring supports...

Hier ein Bltzschuh für die Olympus OM-D E-M5 mit Abdeckung der elektrichen Kontakte des Blitzsteckers. Here is a slash shoe for the Olympus OM-D E-M5 with cover of the electrical contacts of the flash socket. ... Hier die Kostruktion: Here's the...

This slider is created to support an Olympus OM-D camera on the Olympus auto bellows. The main purpose was to be able to copy slides with the additional slide copier. The setup is a combination of the OM-D camera, a 12-50mm lens and an adapter...

Simple seamless lens gears for the Olympus OM 24mm f/2.8 for the use with a follow focus Designed in Fusion360 with the help of GearDXF. ... You can watch the (simple) design process here: https://youtu.be/8_pB6rcDNZg It's a tight fit, so some...

This is an adapter allowing you to use Olympus OM type lens on Gopro 5/6/7 Please note: This has to go without saying but you have to remove the lens cover of the Gopro and the original lens before attaching the adapter with the Olympus lens. How to...

It is the middle-quality low-poly 3D model Olympus OM-D E-M5 used in various fields 3D Graphics such as: game development, advertising, interior design, motion picture art, visualization, etc.. Modeling was made by ortho-photos of real digital camera...