one tbs 3d models

Here is a simple and very small adapter to convert your TBS Source One V3 to a HD quadctoper ! It'll allow you to adjust the pitch of your camera. Works with DJI FPV camera and Caddx Vista as well. It uses the stock HD Camera 4 screws for maximum...

An antenna mount for the TBS Source One (V0.1.1) frame. Print instructionsCategory: 3D Printing Overview and Background Designed to fit standard antenna tubes with an outer diameter of 3mm, for use with FPV quadcopter receivers. ...There is also a slot...

This is a rear mount for the DJI FPV air unit and antennas for a TBS Source one V3. This is a good alternative to mounting it on top of your stack if your stack is tall or if you love the slam life like myself. Tips for proper installation: -The...

Go Pro Session Mount for TBS Source One v3 frame. I tried to make it as safe as possible as well as make sure that props are barely visible with 25 degree tilt and super view setting. This is a 7th iteration of the design and I sort of like it. ...

An antenna mount for the TBS Source One (V0.1.1) frame. Print instructionsCategory: 3D Printing Overview and Background Designed to fit standard antenna tubes with an outer diameter of 3mm, for use with FPV quadcopter receivers. ...There is also a slot...

I built this frame for my TBS source one drone. It's designed to safeguard both the GoPro7 and FPV camera. There's also a mount for video (SMA) and Immortal-T antennas. ... Parts list for this build: SKYZONE SKY04X OLED display:...

Mount for the BN-880 GPS module for the TBS Source One V4 frame. Or any frame with standoffs that are spaced 24mm apart on center. This particular GPS I purchased from RaceDayQuads, but I think all BN-880's are the same size.</p> <h3>Print...

TPU-Parts for the "Peanut Jelly" Build for the TBVS Source one V4 Frame. ...Deisgned to protect the internal electronics as good as possible and still stay as light as possbile - and most important: be sexy instagram.com/yannik.fpv

... end loop back to help thread it through. Although designed for the TBS Source One frame, these mounts fit any M3 standoff. The distance between standoffs for the SMA+GPS tail mount is approximately 30.5mm. ... Best printed in TPU with support.

https://www.facebook.com/StampamiQuesto Complete print set for TBS Source One V0.2 v3 Motor protection and arm ends: protects the propeller from impact up to 40 ° of inclination and moves the impact away from the carbon. super low weight of just 6...

Remixed from FlyHighFPV's TBS Source One Armguard with Skidz Original Project: https://www.thingiverse.com/thing:4397830 I felt that the original was too tall. These are bulky as is, and so I removed some material from the top and bottom of the...

## Update 01.06.2021 - Add new version 2.0 without battery pad cutout and with a thin part for the top indicator light - Add 20° versions of 2.0 --- ## Description I own a Quad based on the TBS Source One V4 frame and wanted to mount the cheap Eken...

This is a set of mounts for the RunCam Hybrid 4K camera on the TBS Source One frame, also compatible with standard single mounting hole micro (19mm) cameras. Files are provided for angles from 20 to 45 degrees in 5-degree increments, suitable for...

A side XT60 / XT60H holder for the TBS Source V5. Just stick it through the standoffs and the XT60 through from below. ... Print with 100% infill made of TPU.

A side XT60 / XT60H holder for the TBS Source V5. Just stick it through the standoffs and the XT60 through from below. ... Print with 100% infill made of TPU.

This is a braced, but flexible, camera mount for the TBS SourceOne V3 for mini (19mm) cameras. ...I designed this after breaking the carbon plates that came with mine.

This set of prints is designed specifically for mounting the DJI Air Unit and antennas into a TBS Source One V3 frame. It's essential to note that these prints have not been tested on the V2 frame, so users should exercise caution when attempting to...

TPU: 209 ° / 30mm / s / 100% infill Riser for Vtx or add-on card device: Press to recover additional space in the back of the build, such as vtx and other 30X30 peripherals Four lower holes for fixing to the bottom of the M3 frame TPU: 209 ° / 50mm /...

Made these VTX and Antenna mounts for a for my new mid range build using the TBS Source One V0.2 Frame. I've used this Banggood LED/Buzzer Combo on all my prior builds, so the antenna mount was designed around this specifically. I printed my stuff in...

So I designed this one so fishing line or other light string is used secure the feed point to the mount. Print the stl as oriented, with supports using TPU. I also recommend using your slicer to apply support blockers to the small rectangular hole...

ImmortalT...) Mount for Vista-Antenna (original) For some more pictures and videos pls check the following link:https://www.instagram.com/reel/CewFqC9Fg0p/ The shown Actioncam-mount is part of my Flexmount and can be found here: [Link will shortly...

This is a custom mount designed specifically for the Foxeer Arrow Mini Pro camera, allowing it to seamlessly integrate with the TBS SourceOne frame system. ...The idea behind this project was sparked by a similar design found on Thingiverse...

ImmortalT...) Mount for Vista-Antenna (original) For some more pictures and videos pls check the following link: https://www.instagram.com/reel/CbDT984lFim/ The shown Actioncam-mount is part of my Flexmount and can be found here: [Link will shortly...

The device is engineered to support a GP Session, but it also functions as an antenna mount for the versatile TBS XF dipole antenna, offering a 25-degree angle of elevation. Designed specifically for use with TPU filament, this print can be...

The DJI FPV system truly shines, but unfortunately, it doesn't fit neatly within the TBS SourceOne frame due to its slightly extended length. This necessitates a minor adjustment, allowing the rear of the SourceOne frame to accommodate the DJI...

Motor wire protector for 7" source one V2 arms Zip ties hidden within print

This is my V2 Runcam Split 2 top plate mount, specifically engineered for the Source One. ...It boasts a stronger design, meticulously crafted directly from the Source One 3D model.

Universal Mounting Solution For All Source One Rear Bumpers And Immortal-T Antennas. ...This Durable Holder Is Designed To Fit Every Version Of The Trusty Source One Frame, Ensuring A Secure And Sturdy Installation Of Your Essential Antenna.

Fits source one frame v3. Mount for 2 SMA a pigtails, small GPS rx, and bardpole. ... Print with your favorite TPU STL and STEP file included if you want to change it up.

This ain't tried and tested yet! ...but just a mount to fit the diversity nano that can be put on a source one, hopefully with enough airflow to not overheat.