one tbs 3d models

I heard you guys like AXII mounts. I've designed this to work with a MCXX AXII antenna. Along with it tube mounts for RF antennas at a 25 degree spread and 15 degree up tilt. Print in TPU 50-70% infill at .016 layer or less. I also added...

I wanted to support the FPV camera using TPU so that the camera housing doesn't crack during crashes. As a bonus, this weighs less than the original carbon fiber plates as well. ... Print in TPU, vertically.

Just a very simple adapter to reduce the holes in the frame for the Vista to m2. I used a small nylon nut to hold the screw in place. ...In this way, the Vista is also isolated from the frame, protecting it from a short circuit on the frame, for...

Same as item remixed from but with a 0.2mm (1 layer height) square added over the holes. This allows for full side to side bridging with other features printed above. screws will just poke through the very thin extra layer. Can be printed without...

Since there are still very few frames for the DJI O3 Air Unit, we decided to make something ourselves. The TPU parts have been printed by myself with Sainsmart TPU on an Anycubic Mega X using Simplify3D as slicer. Unfortunately we had no...

This is remixed mount for SMA adapter that uses M3 screws and M3 heat set inserts for securing adapter instead of M2 nuts and screws.Printed it in PLA+,seems to work fine.

I printed B0bafart's great model but had some issues that I then changed: -made the standoff mounts wider to prevent the rings from separating - made the hole for the antenna lead large enough to fit the U.FL connector (might still need to...

Quick model based on SourceOne V4 top plate

Made these to protect the motor wires from prop strikes and more importantly the sharp edge of the base plate (you could file it down .. but ... ...meh) secure with small zip tie larger version hides zip tie within the print

Moves 30mm stack forward so there is more room for air unit. I sligthly enlarged the 20x20 holes on the bottom plate so they would fit a press nut. ...I put the stand offs where old 30mm holes were and drilled top plate slighty for the screws.

Really strong shell for this thin camera, perfect for hard uses like bandos. To insert the cam you need to cut the shell on the left side, then glue it with super glue and you are ready to rock. Tilt is 28 degrees The monkey edition has...

A rough hack to repurpose RX holders as a VTX antenna mount for axii-style antennas, perfect for those who need a DIY solution. Thanks for sharing this tip, Max! ... - Flakes

https://www.youtube.com/watch?v=MN_E6dyI8hU&feature=youtu.be No more frame on the view Lighter than full size cam More place inside build To be used with bumper if you fly hard like me I do not recommend you to use it I have already...

TPU: Print with 1-2 Wall thicknesses for good damping. ... On the outside of the arm it is slightly thicker for better protection.

Yes its for free <3

little, portable ELRS antena holder, works great very durable, i also upload caddx vista antena holder which combines these two parts very well. ... enjoy :)

This STL is a more design version than this original file : https://www.thingiverse.com/thing:3451679

Simply mirror the design in your slicer for left and right.

Fairly messy model but it prints well and has survived a few crashes. ...I couldn't get other models to fit properly, so made my own.Printed at 100% infill, requires an M5 nut for the GoPro Screw.

A strong and easy to apply shield for the motor wires. Because of the click system you can apply it on already-soldered on motor wires. Advised to print in a upright position for the best looking result. ...(use 3D adhesive if needed) Otherwise if...

A cutting-edge, high-tech action camera mount designed to capture breathtaking footage at a precisely calibrated 28-degree angle, engineered with precision and innovation to achieve maximum stability while minimizing unnecessary bulk.

durable but i recomend using washers for mounting. make sure the bottom off the mount is on the printer bed. ...made with tree suport and tpu.

Receiver and VTX Antenna Mount Now Available in SMA Version.

I needed a more substantial base for the S1, so I reworked several concepts to create something more robust. The main frame is constructed with TPU for added durability. ...The mount's angle is set at a precise 30 degrees.

Designed this soft mount to reduce the motor vibration transfer to main body. Print of very soft tpu and install to both sides of arms. You need 6mm longer stack and arm attachment screws to assemble this. Remember to use loctite! ...

A tiny bracket is needed to secure an R-XSR to the rear standoffs. ...Wrap a compact cable tie around the hole, then seal it with heatshrink tubing as you connect the antenna.

Compact GPS holder measuring 18x18x5 millimeters.

Receiver and vtx antenna mount. ... Now also in a SMA version.