orange pi plus 2e case 3d models

Definitely use a safety lanyard or chain between the door opener arm and the door just in case anything breaks (see photos). I designed it to use the same mounting hole spacing that already existed on our doors and added generous slots to...

The heater is faced with the intake fan facing the back of the case as I didn't want air rusing across the build area DUE TO RISK OF FIRE YOU MUST RUN THE HEATER WITH A THERMOSTAT CONTROLLER! Do not under any circumstance just leave the heater...

You can do this by using 0.1mm layer height and then rounding up (for example to next 0.1mm or 0.2mm - or even 0.4mm or more in some cases) until you are satisfied. If your printer is calibrated exactly, this won't take long to get to but it is...

I used these files which are small but about near perfectly sized for this: https://www.amazon.com/gp/product/B07WDCBJ1G/ref=ppx_yo_dt_b_search_asin_title?ie=UTF8&psc=1 I also used an emory board to sand the bulges off around the corners in some...

In this case, please contact, it is possible to save files at high values, but this will give a sharp increase in file size. This is a fully solid-state version for 3d-print, this is not a scan version. At the photos you can see the contours of the...

In the case of doing a cut-stone corner, where one side is a wall, and the other side is a special piece (arrow slit, window, door, etc), rather than using a pillar, you can use one of the cut-stone wall backs from the wall construction kit. Also...

In the case of Khafre, he and his sculptors managed to express their vision of kingship visually, and in many ways more succinctly than could be done in words alone.  Who was the intended recipient of this message? Perhaps it was intended for no one,...

However, we also had some false triggers and cases of missing cheese but no captive critter. One of the little fellows had the audacity to take the cheese and leave poop in the trap. Another one ate the cheese and then made his own exit hole in the...

Scenery or Bases Scenery objects or bases are often designed to be printed directly on the build platform, and in this case, are not supplied supports.    Back our Patreon or Join our MyMiniFactory Tribe!Each month we release a new set of digital...

In this case repeat again for color 12. This will probably be pretty handy for this model as there is a bunch of swaps in the 1 AMS profile and this will ensure you don't miss them. If you do not have Bambu Studio/Orca I recommend using it to look...

Relatively permanent mount on the rear saddle rails for Topeak QuickClick compatible saddle bags. I made two versions: one flat (original design), & one round so you can slide the whole mount along the rails to find the ideal position. I also...

The 4'th wire is spare, in case I want to strobe the LED brightly from a separate supply. Results: First light! (after a little detour upgrading firmware - don't trust the included bootloader!) Send: M48 Recv: M48 Z-Probe Repeatability Test [...]...

Applications and Use Cases: Advertising and Marketing The model is perfect for creating mouth-watering visuals for advertising campaigns, both digital and print. Its realistic appearance makes it ideal for promoting pizza brands, restaurants, or...

In any case, Jeanne couldn't qualify as a maîtresse-en-titre unless she had a title; this was solved by her marriage on 1 September 1768 to Comte Guillaume du Barry's brother. The marriage ceremony included a false birth certificate created by Comte...

If you need an all-rounder that can take a beating, go for the v10 unless you have more time, in that case go for the v13. ## Modifying it in Blender !! The next section of the description is for modifying the model, so don't worry about it if...

As long as your center hole and center bolt pattern is actually on center, this will be the case. Once the top print is bolted in place, take a sharpie and mark the template for the intake tube hole. Unbolt the top print and cut out the marked...

*I used a raft on: eyebrow_left/right, eye_blacks, eye_white_left/right, tail_black, hair 3-The eyes are extremely small, so you may want to print a few in case you lose them. .. Assembly tips: 1-Take your time gluing the model together...

In this case, increase the "stand_height" parameter so the lower shelf is further up off the table. Remember that the weight of the tubes will now be borne by the top shelf, not the bottom. It's possible to use only one shelf if you hand-tweak the...

Like… very-nearly-the-whole-MK3s-build-plate-big, so don't be surprisedSettings (how I printed mine, at least):Prusa Slate Silver PETG0.4mm nozzle.2 layer height20% infill (resulted in some surface scarring, but it's not visible on mine when in...

The end of the tacks WILL need cutting down so they clear where the batteries will be and the center of the design may need additional filing down depending on how much solder is used.Run a little bit of superglue down the edges of where the TP4056...

In that case, you will need to use gcode to set the correct uSteps and eSteps after the hard reset. For 1:1 drive extruder (standard for BEAR): M350 E32 M92 E280 M500 For 3.5:1 drive extruder (vertigo pulley box): M350 E16 M92 E490 M500 Send M503 to...

Bolt sizes for shaft and motor case were decided, holes scaled appropriately. A diametrically polarized tube-type rare earth magnet was found and measured. Planetary arrangement of gears was scaled to fit within desired package size. System designed...

Place the GoPro in the case the slide it into the mount from the underside. Insert the last bolt (the short one) to secure the GoPro. If you have rubber hair on your tyre it might hit the GoPro as it spins and make an irritating sound both for you...

It may be wise to print extra copies in case you drop them. 4 - When removing parts from the printer bed, it's a **VERY** good idea to place left/right parts into separate containers to help with the assembly process. Sometimes the difference between...

The arrow points up and would align with the top edge of the to holder not including the cap storage protrusions and is exactly as wide as the holder.in case you need to mount this right next to something. Hope this helps. ... Category: Tool Holders &...

Many table holders we saw failed to deliver or only worked if you didn't have a case on the tablet. Or they may only work with either phone or small tablet, or they don't support having cable connected to the device while charging. We conducted...

I printed multiple copies at the same time with no brim and they came out perfect, however this part could be tricky if you have problems with bed adhesion. .. 4-hair_top contains a built in support structure that needs to be removed after printing....

It would be wise to print extra copies in case you drop them. 5 - In general for all my models, when removing parts from the printer bed, it's a **VERY** good idea to place left/right parts into separate containers to help with the assembly process....

- I have added the part "G-BendyArm_x_2" to the file list in case you don't own any GoPro connectors. You can also find various sizes and shapes of these connectors here on Thingiverse. ... - the part "F-TripodMount_x_1" connects to your tripod mount...

Not a problem with a well-tuned MK3S+.    The box was printed usingFilament                                              ...