orange pi plus 2e case 3d models
302987 3d models found related to orange pi plus 2e case.
thingiverse
В нем установлены: - Одноплатный компьютер Orange Pi zero 2 - Твердотельное реле - Розетки 220 В для ввода питания и подключения 3D принтера - Выключатель для включения/выключения принтера без участия ПО сервера Octoprint - Вентилятор охлаждения...
thingiverse
I liked a few models for Orange Pi Zero: https://www.thingiverse.com/thing:2551381 https://www.thingiverse.com/thing:3652160 https://www.thingiverse.com/thing:2855465 Created a model of the mixing of these models into one. The antenna is rotated 90...
thingiverse
I included the original Sketchup file I used to design this, so customize it to your heart's content ## ORIGINAL: Since Orange Pi Zeros have an overheating issue (mine does), I figured I'd create a minimalized 'open air' tall case with a 25mm 5v DC...
thingiverse
3D Model View Assembly I've built a Handheld Game Console powered by Orange Pi Zero Plus 2 (H3 version). The console features a 4.3" screen sourced from a car rear camera view monitor. The dimensions of the device are 186 x 81 x 26mm. ... I started...
thingiverse
Compact, ventilated enclosure for Orange Pi Zero 2 SBC! Disclaimer: This box does not contain ANY mountings to anything so if you want to mount this to a 3D printer or somewhere else, it's best to use double-sided adhesive tape. Also, there is...
thingiverse
This is a modified version of the original case featuring the logo from the r2con 2017 event.
thingiverse
Remix With Mounting For My Case -- 4mm Mounting Holes Are Standard Customize Your Mounting Points Here: https://tinkercad.com/things/1abQga3NVEy
thingiverse
There are four versions of this case available: * Kodi with a non-removable SD card * Kodi with an SD card slot * Non-Kodi with a non-removable SD card * Non-Kodi with an SD card slot All the cases utilize the same bottom panels. ... Printing Settings:...
thingiverse
Based on the original case design, I remade it from scratch using FreeCAD for seamless integration with the Dagoma DiscoEasy 200 3D printer.
thingiverse
... first case based on the OPi Zero 2. ...The SoC keeps at around 60 to 70°C with a small heat sink in use and light use (Spotify, Bluetooth, Airplay Receiver). For now, the antenna is inside the case, but an antenna holder should be added at the back.
thingiverse
... 03/14/17 I redesigned the case and rearranged the antenna holder to fit inside one position. I use 2.5*12mm screws. To-Do List: 1) Add a removable lid to the case for easy access to GPIO pins. 2) Install a window for the IR receiver in the case.
thingiverse
... if desired. Printing requires no supports, just place the flat side of each half on the print bed. To assembly, carefully guide the 4 clips to their slots. **Update 08-23-2023** - added a version of the case top with a 16x16mm heatsink opening
thingiverse
Update 07/03/23: Fan doesn't fit inside the case. It can be mounted outside but the grill has to go. Hole for old PCs 50 mm fan. ...Also added a hole for the IR receiver since PLA is opaque.
thingiverse
A remix of Adolf_Muffin's case to mount to extruded aluminum, all credit goes to them for this design. ... No supports required, I added a custom support to the model that prints a 1 line thick support that can be easily snapped off.
thingiverse
The case is a bit cramped, there is a possibility of breaking the memory card when dismantling the board. The screws for fixing the board are M3x6, for the fan - M3x25. The thread for the screws must be cut by yourself. ... Overall size with fan and...
thingiverse
... grabs the TV to the wall. ...The base is taken from this TV support https://www.thingiverse.com/thing:4461630 And I got the measures to place this case https://www.thingiverse.com/thing:5761356 . ... Excuse me if you see any error, I do not design.
thingiverse
Remix of the Case by Xoan The Top Part is Simplified for Easy Integration with GPIO To facilitate seamless connectivity, the upper section has been optimized to work in harmony with the General Purpose Input/Output (GPIO) system. ...This streamlined...
thingiverse
... to save you like an hour of printing time because there is no reason for a 2mm thick bottom on this thing. The screw holes now go all the way through the bottom of the case to give you a little more flexibility on the length of screws used.
thingiverse
Remixed from the excellent design by powermos (https://www.thingiverse.com/thing:1565411) Working on the bottom shell, I added four extensions along the edges, allowing the case to be mounted on a plate or standing vertically. The top shell is...
cults3d
... a hexagon design for airflow. ...I also designed a 1 rail version as my Tronxy printer had room for the Pi on the back rail behind the power supply. Just use some 3m screws to close the case. ... Thanks @deez2009 and @ender1968 for the initial designs.
thingiverse
... design for airflow. ... I also designed a 1 rail version as my Tronxy printer had room for the Pi on the back rail behind the power supply. Just use some 3m screws to close the case. Thanks @deez2009 and @ender1968 for the initial designs. ...
thingiverse
Orange Pi Lite case with a 30mm fan mount and an optional buck converter case and small PCB holder for connectors. To attach additional 4-channel relay switches, visit https://www.thingiverse.com/thing:2674120. For OctoPrint setup, refer to...
thingiverse
Here are 2 Orange Pi Zero cases: one for 26 pin connector with pins UP, and another with pins to the SIDE. ...Please send photos if you get to use them!
thingiverse
This is a quick-assemble case designed specifically for a raspberry pi Zero W and connected IQAudio Pi Zero DAC plus Headphone Amp. The top and bottom pieces take approximately 1.5 hours to print. Assembly: 1) Attach one M2.5/9mm standoff to the...
thingiverse
If you cannot print the case yourself, you can obtain the 3D printed parts only from the following address: https://retropicases.com/products/zx-spectrum-plus-3-raspberry-pi-cases-with-working-led If this Spectrum Plus/3 isn't your cup of tea, I...