orangerx spektrum 3d models
791 3d models found related to orangerx spektrum.thingiverse
... mod. Instructions Remove cover from OrangeRx DSM2/DSMX module Unscrew antenna jack from old cover Attach antenna jack to new cover Place your 3-D printed insert inside the case to retain the PC board Screw your new 3-D printed cover into the case
thingiverse
Remix of "OrangeRx Spektrum DSM/DSM2 JR module replacement cover -- Antenna relocation" by abobotek (thingiverse.com/thing:391383). This thing is a cover without the antenna hole for those who relocated the external antenna of the OrangeRx module. ...
thingiverse
R610 OrangeRX receiver template. ... Designed with SpaceClaim (file included).
thingiverse
OrangeRX R910 DSM2 9 Channels receiver template. ... Created with Designspark Mechanical (file included)
thingiverse
A replacement OrangeRX, JR module cover which moves the antenna SMA port to a usable position.
thingiverse
So I made a small box for my OrangeRX DSMX/DSM2 Compatible 2.4GHz DIY Transmitter Module. Nothing fancy, holes so antennas and wires can poke out and room for the transmitter module and a FrSky D8R-XP Plus it matches my LiPo battery tray ...
thingiverse
This is a cover for OrangeRX 433 MHz module installed in my Taranis QX7. I've picked several designs around and mixed into this one. To sumarize, this one has: - Antenna realocated to the top of the module - Antenna slot has an indentation to...
thingiverse
I'm planning on installing the transmitter module from the OrangeRX as a receiver to my S800 Sky Shadow. The original case for the TX module is quite big so I wanted to try to make a bit smaller 3D printed case for it. Managed to get it done and for...
thingiverse
I decided to make another OrangeRx transmitter antenna mount. It supposed to be glued on stock back cover and not close pins for programming. It has maximum height to be fit without problems. Thing consists from two parts. First, disassemble...
thingiverse
Here's a rough model of the HobbyKing OrangeRX 6ch receiver. ...Use this for planning your model layouts.
thingiverse
Alternativ cover for Taranis OrangeRX http://www.hobbyking.com/hobbyking/store/__24656__OrangeRX_DSMX_DSM2_Compatible_2_4Ghz_Transmitter_Module_JR_Turnigy_compatible_.html Used Pigtail...
thingiverse
This will provide native automatic DSM2 / DSMX functionality with full range (200mW instead of 100mW) transmission strength, aircraft binding through radio interface instead of a button on the back, and model match capability using true spektrum...
thingiverse
For those that have broken the small hex end of the Rotary selector in the OrangeRX TX6i. While I have included the complete wheel design for reference, in practice I printed without the center shaft, drilled a 2mm center hole instead, and...
thingiverse
This is a simple case and cover for the OrangeRX OpenLRS 9 channel receiver. Features openings for all onboard pin headers. UPDATE: according to the comments, there is another version of the board that has 4 extra pins soldered on. I have added the...
thingiverse
The OrangeRX OpenLRS reciever from HobbyKing has a non-flat bottom which makes it hard to mount. So I made this thing to fix that! Just slide your RX into the grove and now you have a nice flat bottom to stick/screw/velcro to your remote control...
youmagine
This is a small model to relocate the SMA connector (without modifying the case) for the most recent model of the OrangeRX DSMX JR module (with the screws on the back/bottom) from coming straight out, up 90 degrees. Make sure you print the main...
thingiverse
Since i started using the OrangeRX DSM2/DSMX module for my Turnigy 9X transmitter i have been annoyed by the fact that the transmitter cannot be placed on its back, since it would rest on the module antenna. This custom lid fixes that problem by...
grabcad
Spektrum AR8000 reciever See: Spektrum AR8000 satellite (cable ca. ...155mm) Spektrum TM1000
prusaprinters
This is a small model to relocate the SMA connector (without modifying the case) for the most recent model of the OrangeRX DSMX JR module (with the screws on the back/bottom) from coming straight out, up 90 degrees.Make sure you print the main...
thingiverse
For Spektrum DX3 to replace ageing foam wheel with 1/10 scale touring car tire
youmagine
This is a mod to fix the terrible antenna position on RC transmitter modules, specifically the new OrangeRX DSMX JR/Turnigy/Spektrum module. The existing mods on Thingiverse did not fit my transmitter module, so they must have changed the module...
grabcad
http://www.hobbyking.com/hobbyking/store/__27096__OrangeRx_Open_LRS_433MHz_9Ch_Receiver.html?strSearch=OrangeRx%20Open%20LRS%20433MHz%209Ch%20R
thingiverse
This is a 50mm plate with mounting holes (M3) at 45mm distance with a mount for the OrangeRX OpenLRS receiver from Hobbyking.
thingiverse
Adapter für das OrangeRx-DIY-Modul 2,4 Ghz für den Taranis Modul-Schacht Print Settings Printer: Wanhao i3 V2.1 Resolution: 0,2mm Infill: 40%