orenda 14 3d models
73688 3d models found related to orenda 14.grabcad
This is the intake casing for an Orenda engine containing the compressor intake guide vanes and acts as a support for the bearings and power take off gearbox which I will be publishing shortly. ...I am up loading the entire engine in parts because it is...
grabcad
I have almost completed this Orenda engine so it is time to start uploading. The entire assembly is very large so I am going to do it a bit at a time. All the information I have got is based on workshop manuals bought off Ebay, there are a number of...
grabcad
This part takes the air from the compressor and guides it into the combusters and is surrounded by the firewall. ...Both parts are supported by the backbone not shown.
thingiverse
Customized version of http://www.thingiverse.com/thing:172274 Created with Customizer! ...http://www.thingiverse.com/apps/customizer/run?thing_id=172274 Instructions Using the following options: bold = Yes text = #14 Stewart canh = 128
thingiverse
... version of http://www.thingiverse.com/thing:50908 Created with Customizer! ...http://www.thingiverse.com/apps/customizer/run?thing_id=50908 Instructions Using the following options: teeth = 14 holeSize = 5 scale = 100 type = Spur hole = Yes height = 5
thingiverse
Customized version of http://www.thingiverse.com/thing:2044157 Created with Customizer! ...http://www.thingiverse.com/apps/customizer/run?thing_id=2044157 Instructions Using the following options: hexnut_d = 14 bearing_h = 7 bearing_d = 22.1
thingiverse
http://www.thingiverse.com/apps/customizer/run?thing_id=834725 Instructions Using the following options: Font_name = Sigmar One center = 60 Loop_x_position = -34 Rotation = 50 spacing = [10,18,21,14,15,15,15,15,15] Text = 14 height =...
thingiverse
... Created with Customizer! ...http://www.thingiverse.com/apps/customizer/run?thing_id=753477 Instructions Using the following options: extrude = 6 web = 0 font = Great Vibes text = 14 size = 20 direction = ltr spacing = .6
thingiverse
http://www.thingiverse.com/apps/customizer/run?thing_id=52734 Instructions Using the following options: message = Rm 14 Hall Pass stick_thickness = 7 font_thickness = 7.5 flat_bottom = 1 stick_width = 17 Font = write/orbitron.dxf hole_radius = 5...
thingiverse
http://www.thingiverse.com/apps/customizer/run?thing_id=101307 Instructions Using the following options: build_plate_selector = 0 Keychain_Style = Tag text9 = text8 = text7 = text6 = text5 = text4 = text3 = text2 = text1 = 14 build_plate_manual_y =...
thingiverse
http://www.thingiverse.com/apps/customizer/run?thing_id=739573 Instructions Using the following options: text_thickness = 4.2 outline_thickness = 3.0 lug_width = 0 bar_style = bar_only glyph_coalesce_strategy = bar and glyphs outer_margin_width = 1...
grabcad
The turbine is supported by the rear bearing and like the bearing is subject to air flow derived from the compressor for cooling. ...The blades are retained by pins which are sheared off when removing the blades for cleaning etc.
thingiverse
http://www.thingiverse.com/apps/customizer/run?thing_id=739573 Instructions Using the following options: font_narrow_widen = 0 inner_margin_width = 1.5 whichextruder = monochrome bar_length_trim = 0 lug_length = 4 bar_style = surround_text...
thingiverse
http://www.thingiverse.com/apps/customizer/run?thing_id=739573 Instructions Using the following options: minimal_color_layer_thickness = 0.6 font_narrow_widen = 0 font_size = 12 text_thickness = 4.2 character_spacing = 1 outline_thickness = 3.0...
grabcad
This is the front bearing that supports the compressor spool and embody"s the oil spray and rear oil seal.
grabcad
The outer manifold supply's cooling air into the centre of the cone and also helps cool the turbine bearing shroud as well as the support structure.
grabcad
This unit transmits power from the front gearbox to the hydraulic gearbox which I will upload later
grabcad
This part guides the hot gases on to the turbine. The nozzle shroud is surrounded by cooling air pumped into the housing and by the cooler bypass air from the outer parts of the combuster. ...I have left out the bolts and other fasteners for clarity.
grabcad
This is the name given in the manual but it also provides power for other accessories and derives its power from the upper bevel drive. ...It is mounted on to the upper compressor casing.
grabcad
This is one of the 6 combusters, the inner part splits the air flow between the inner air flow for the burner and the outer air flow for cooling the air to a more manageable temperature and also protecting the combuster and adding additional air. ...I...
grabcad
Here is the compressor spool for the above engine,It comprises of 9 seperate stages getting progressively smaller building up the pressur, it is driven by the turbine and is in turn supported by the front bearing and the centre bearing and is...
grabcad
These are the casing that hold in place the guide vanes that comprise the stator parts for the compressor. The outlets provide cooling air for various parts of the engine and are connected to pipes running alongside the engine. Only the first three...
grabcad
This would be a complete assembly on a real engine and effectively takes the compressed air from the compressor section and uses it to burn fuel to provide the energy to drive the turbine. Most of it is air cooled derived from various stages of the...