original prusa mk3 raspberry pi 3 hat and raspberry pi zero einsy rambo box by 3d models

The following Raspberry PI models are compatible: * Raspberry PI 3 Model B+ * Raspberry PI 3 Model B * Raspberry PI 2 Model B * Raspberry PI 1 Model B+ Cable Requirements: * A Dupont connector 4-pin male for connecting the Pi to the Einsy board. * A...

So I modified the display box file and added this side mount for the pi zero. No support needed.Ideally one should use the w version without the GPIO pin soldered. It should be also possible to change the orientation and moun the wh version, although...

... you have a little overextrusion, the fit may be too tight, so I'm also including a version with a slightly smaller ball. You may want to print both an see which one works better for you. More information and download STEP and Fusion 360 files here.

... with a slightly smaller ball. You may want to print both an see which one works better for you. [More information and download STEP and Fusion 360 files here.](https://arcady.genkin.ca/2021/02/raspberry-pi-camera-mount-for-prusa-mk3-s-mk2-s/)

This is a revised version of the Einsy case with Pi Zero W, adapted from llj3663's original design on Thingiverse (https://www.thingiverse.com/thing:2862375), to utilize the stock RP0 mount and back cover in place of the door, which I found didn't...

I've designed this holder with ease of installation and removal in mind, directly from the Prusa MK3 frame without needing any tools. The holder is specifically crafted to fit the case found at https://www.thingiverse.com/thing:3001109, created by...

The holder is desing to fit the case: https://www.thingiverse.com/thing:3001109 by dghoti Thanks to him for the case Print instructionsCategory: 3D Printer Accessories Print Settings Printer Brand: MK3 Printer: Prusa i3 Rafts: No Supports: Yes...

... opportunity to integrate the sleek Alu Case into your Prusa Mk3s Printer setup. This enhanced design offers a more refined and organized printing experience, making it an attractive option for those seeking a higher level of precision and control.

Important note: This mount was specifically designed for Raspberry Pi's OEM v2.1 Camera. Using any other camera may result in damage to the camera. ...Most fit issues are caused by non-OEM cameras, so please use caution when experimenting with...

This is a remix of my previously designed Display box with Pi Zero2 mount. Commonly seen 15cm cable is not enough if the camera is mounted on Xmotor, since a high Z position will disconnect the camera. I am inspired by the ball joint camera...

A simple mount for the Raspberry Pi camera on the Prusa i3 Mk3. Inspired by https://www.thingiverse.com/thing:2636887 but redesigned with a slightly shorter arm and a better fit for the Mk3. ... It uses the camera case from...

Remix of Lab27's "Prusa I3 MK3 Raspberry Pi Camera Mount" (source: 3121052) The camera position has been raised by 10mm from the original mount. This remix prints with the 'cup' feature facing upwards. ... No changes were made to the camera enclosure...

Prusa i3 mk3s board case with Raspberry Pi

This is a simple print to hide/protect the Raspberry Pi Zero (or the Einsy Board if you have removed the RPi like I did).I copied the style from the original cover and printed it in black PLA on a textured sheet to make it blend in with the other...

A simple mount for the Raspberry Pi camera on the Prusa i3 Mk3. ...Inspired by https://www.thingiverse.com/thing:2636887 but redesigned with a slightly shorter arm and a better fit for the Mk3. It uses the camera case from...

This is a compact enclosure for a DHT sensor, Raspberry Pi Zero W, and OLED display. The casing appears to be adequate, but temperature readings are contingent upon the Raspberry Pi's internal temperature. Made from PLA 1.75mm filament, this project...

All the original parts from Thingiverse (https://www.thingiverse.com/thing:3114849) were printed with 3 outer perimeters and 15% infill, which seems to create rigid enough parts. Ballpoint_solid and Prusa_plate_camera_mount_v3 were printed with 3...

I needed a Raspberry Pi Bracket for the right side of my Prusa MK3S printer bed to work with the common Pi Camera Mount. I wanted to use the MK3's Extrusions to mount too so that my Pi Camera cable would line up properly and I would be able to use a...

This articulating design has 24 indexes on each link connection point and a knurled nut so you can easily lock it. LINKS: There are 3 different link styles that can be put together however it suits your needs. Links are held together with knurled...

Also connected the ballnut with slightly modified fflink as I don't need them as separate parts All the original parts from https://www.thingiverse.com/thing:3114849 are printed with 3 outer perimeters and 15% infill which seems to create rigid...

The case for the Raspberry Pi 2/3 attaches securely to the back of your Prusa i3 MK3, directly onto the frame just above the electronics. This thoughtful design leaves ample space for a completely unobstructed Z axis with its accompanying wiring. The...

This creation brings together the effortless connection of ironhalo's arm with the robust stability of rwohleb's ball and socket joint system.

This simple mount is designed specifically for the Raspberry Pi camera on the Prusa i3 Mk3 3D printer. The design takes inspiration from a previous creation found on Thingiverse, but with some key improvements to better fit the Mk3 model. ...A shorter...

Computer box pour Raspberry PI. ...Intègre un écran tactile de marque "WaveShare" 7''. Compatibilité RaspberryPi 4 Raspberry Pi 3 Model B+ Raspberry Pi 3 Model B Raspberry Pi 2 Model B Raspberry Pi 1 Model B+

The camera case is designed specifically for the Raspberry Pi Camera Module v2 and uses a simple snap fit design. The camera case attaches with a snap fit ball pivot to the arm, allowing you to adjust the horizontal and vertical angle easily. This...

raspberry pi Zero ups/ pmu module hat by Leadslab

raspberry pi Zero ups/ pmu module hat by Leadslab

I am inspired by the ball joint camera mount from Prusa MK2.5 Camera Bed Mount Ball and Socket (https://www.thingiverse.com/thing:3074504). So I added a ball joint to the top of the display box. In this way you can also exploit the extra rotation of...

Case Upgrade for Pi Zero Plus Raspberry Pi TV HAT No additional fasteners required, no extra structural components. ... Furthermore, additional resources have been uploaded: FreeCAD design files for customizations and enhancements.

Couldn't find a simple camera mount for the raspberry pi camera on the Prusa MK3, so I designed one myself. Inspired by the many mounts on the X-axis motor - what a fantastic idea! To attach to the X-axis motor, I used an M3x18 screw. I secured it...