paneldue 7i 3d models

Paneldue 5i clone mount for use on my Hypercube. Used F2D-SolidInk's design as a base for the display housing. Print 1 housing, 1 angled mount, and 1 mirrored angled mount to use. solidworks file included for modifying the bracket if needed. ... ...

A simple remix of the PanelDue 5i front case piece to suit mounting to the Seckit SK-GO. ...This part is required as well as the "5i_Case_Rear.stl" part from the original file set: https://www.thingiverse.com/thing:2799628/files Category: 3D Printer...

Here is a simple mount for the PanelDue 5i that perfectly complements the Anycubic Delta Linear Plus. It prints flawlessly even without any support structures, which is a major plus in my book. ...However, one thing to keep in mind is that you'll need...

A simple redesign of the PanelDue 5i front case piece to fit mounting on the Seckit SK-GO, necessitating the inclusion of this component alongside the "5i_Case_Rear.stl" piece from the original Thingiverse file set located here:...

Changes Implemented: * Swapped out the mount to accommodate a non-standard LCD screen, replacing the stock LCD of the Anycubic Predator * Created additional space for integration with the PanelDue board * Upgraded the ribbon cable to 10 ways,...

The design consists of three distinct components: A face plate that securely encloses the PanelDue and 7" LCD A replacement panel designed specifically for the upper section of the Rostock printer An adapter that seamlessly interfaces between the...

... ducts. This has worked well on multiple displays over several years without issue. The PanelDue 5i case needs supports only for the SD card slot opening; no other support is required. ...I printed it with PLA since high heat is not involved.

... it. This integrated version features a high-quality, custom-made 5 inch or 7 inch TFT LCD panel from a top manufacturer, paired with the PanelDue controller by David Crocker on the LCD's PCB. ... If you enjoy our models, be sure to let us know!

PanelDue Enclosure with 5 Inch Touch Screen Cable access is conveniently available from either side or bottom. Three 6mm M3 screws secure the enclosure in place. Ten millimeter M3 screws hold additional components firmly. Twelve millimeter M3 screws...

This is my take on a case and frame mount for 2040 extrusion, specifically the Misumi variety, and the v2 of the Paneldue 7" screen. The screen attaches to the front of the case via four M3 10mm screws. The back section secures to a 2040 profile...

I purchased a FYSETC PanelDue clone (https://www.aliexpress.com/item/4000152814384.html), and I soon discovered that "clone" is not an accurate description, as it's more like an inspired design. It was clear from the product images that this device...

I bought a FYSETC PanelDue clone, available at https://www.aliexpress.com/item/4000152814384.html, and upon receiving it, I realized that "clone" might not be the best description since it is more like an inspired design. From the product images, I...

This is a display housing for the FYSETC PanelDue, designed for the Snapmaker J1, but it might be useful for other printers as well.  The buttons on the back of the PanelDue can be pushed from the side by levers that are integrated into the case if...

Remixed from https://www.thingiverse.com/thing:3525265 which itself is a remix of dc42's original PanelDue mount https://www.thingiverse.com/thing:656884I extended the left side of the case so it's symmetrical, and used the extended space to house a...

PanelDue 5i case with usable SD card access. Uses 7 M3 4mm x 3mm inserts and M3 bolts (4-18mm and 2 6mm) or longer M3 bolts (4- 22mm and 2 8mm) and nuts. Many people say a 30cm cable is the longest you can use reliably with the SD readers but I made...

This is a case for a Duet 2 Wifi PanelDue 4.3 inch.The switch on the top left (19mm) is a 230V switch to turn on the printer. In order to shield the user from the 230V line, the switch is additionally protected in the housing.The switch on the bottom...

Enclosure for the PanelDue with 5 inch touch screen. Cable access from the side or bottom. 3x 6mm M3 3x 10mm M3 4x 12mm M3 1X 30mm M6 and nut 3x 25mm M4 and nuts Updated this with a hinged attachment part for moving the screen out of the way of a...

PaenlDue Slim case for the PanelDue 5". It's a total of 16mm thick. Versions and info I've uploaded two versions of the enclosure: * Version 1 has nuts on the rear side with M3 screws going through from the front. * Version 2 has internal M3 thread...

This is a front mount bezel designed for the PanelDue 5i used in Wanhao Duplicator 6 or Monoprice Ultimate 3 printers. It's low-profiled and matches the curve of the chassis for a sleek look. A door can still be used, but the front edge will need to...

You'll be able to attach a PanelDue to your Rostock MAX METAL by mounting it directly on the frame. Or you can modify the mounting bracket if you prefer! This design uses captive M3 nylon locknuts along with M3 screws. Four 5mm screws are used for...

The housing fits perfectly with the "semi-integrated" Chinese version of the PanelDue V3, which can be found at https://www.aliexpress.com/item/4000152814384.html. I chose this version over the original due to its compact form factor, featuring the...

I made my own 4.3" PanelDue Touchscreens because I wasn't entirely happy with the available options. The result is a compact case that looks great in person. However, the print settings can be tricky to get right, so feel free to skip it if you...

I didn't entirely like any of the available options for 4.3" PanelDue Touchscreens, so I made my own. With a faux carbon fiber twill faceplate, even! The effect is hard to capture up close on camera, but looks great in person. It's also a tricky...

I didn't entirely like any of the available options for 4.3" PanelDue Touchscreens, so I made my own. With a faux carbon fiber twill faceplate, even! The effect is hard to capture up close on camera, but looks great in person. It's also a tricky...

The 3D model has been meticulously crafted based on real measurements, ensuring accuracy and a high level of fidelity to the original design. Formats include .max (for 3ds Max 2008 Scanline and V-Ray), .fbx, .obj, .3ds, .mb (Maya 8.5), .lwo, and .c4d...

*** I’m no longer posting to Thingiverse, or Updates. If you wish to see all my work and updates to items posted to Thingiverse please visit my personal website https://gallaghersart.com/design ,OR Google “GallaghersArt 3D” (GallaghersArt is a single...

Securely Connect the Power Cord Directly to the Stationary Bike.

This is a custom enclosure designed specifically for the 7-inch display.\r\n\r\nIt features an intuitive interface with real buttons, easy SD card access, and provision for two 6mm shaft switches, ideal for those who need them.\r\n\r\nMeasurements...

This is so I can move the Duet 7” screen around a little **screen handheld part done, working on PC, and rail mounts for the handheld. Parts • M3 tap/ bottom tap • 8x M3 heat insets (holes are 5mm) • 6x M3 bolt • 2x M3 bolt Enjoy! ... `mike

This is so I can move the Duet 7” screen around a little **screen handheld part done, working on PC, and rail mounts for the handheld. Parts • M3 tap/ bottom tap • 8x M3 heat insets (holes are 5mm) • 6x M3 bolt • 2x M3 bolt Enjoy! ... `mike