paracord spool 3d models
52933 3d models found related to paracord spool.thingiverse
This is a basic Paracord spool. Diameter 55mm. Only needs a 2 threads and threaded rod for complete. ...
thingiverse
Paracord Spool size 84x100x4 mm [Workshop-3d.ru](https://workshop-3d.ru/) [Buy me a coffee](https://www.buymeacoffee.com/ws3d)
thingiverse
A paracord spool I designed. To fasten the ends I did an overhand knot through one of the holes and wrapped. ...Designed for Paracord 550, but works for similar rope.
thingiverse
Very slightly modified version of the source [Paracord Spool](https://www.thingiverse.com/thing:4831426) by echomirage. ... The stl files actually contain ~7 meshes each, which intersect in complicated ways, but can be split apart if necessary for...
thingiverse
This is a simple paracord spool that is meant to hold up to 3.0mm cord. There are multiple holes to assist in winding and cleats on the size to hold the cord ends. The larger hole in the one arm can be used with a small carabiner to clip to...
prusaprinters
A spool which holds about 75' of 5mm paracord. Could be scaled up or down to hold more or less cord. ...There is a hole in the center to thread the paracord through.
cults3d
Small spool i designed for my paracord. ... I designed it to be printed in 2 parts to eliminate the need for supports and then used super glue to permanently join them together.
thingiverse
Small spool i designed for my paracord. I designed it to be printed in 2 parts to eliminate the need for supports and then used super glue to permanently join them together. ...
thingiverse
2021/04/28 Update: I have adapted the Yarn Spooler to work with these spools: https://www.thingiverse.com/thing:4843173 This spool was designed for organizing and dispensing a selection of 550 Paracord. I have multiple colors for various projects,...
prusaprinters
I have not yet tested them.2021/04/28 Update: I have adapted the Yarn Spooler to work with these spools: https://www.thingiverse.com/thing:4843173This spool was designed for organizing and dispensing a selection of 550 Paracord. I have multiple...
thingiverse
Paracord holder based off bbrown1951's design. Updated to fit Stanley blade 61mm x 18mm blade, blade door held in with 2.5mm old laptop screws and holes oversized to compensate for filament spread. However the door shuts quite well and you won't...
thingiverse
This is a Remix of the Paracord Spool by Redpool (link below). I removed some of the internals for a simpler print. ... https://www.thingiverse.com/thing:1634422
thingiverse
This is a Paracord spool with attached tools. It holds about 65ft of 550 or 750 Paracord, and has a paracord cutter and a holder for a standard Bic Lighter. The rings at the corners are large enough to tie the end of the paracord and also large...
thingiverse
This is version 2 of a paracord spool that I designed. I removed the carabiner hole and replaced it with a larger hole on the side which acts as a pivot point to pinch while unwinding cord. The spool will pivot back and forth to allow for faster...
thingiverse
A paracord spool with a cutout for a razor blade and 2 notches for holding paracord ends. The hole in the bat's head at the top can be used to attach a key-ring and/or carabiner. Very lightweight and requires little filament but still very strong. I...
thingiverse
A simple ladder spool for paracord. ...Use it for paracord 550 up to 100ft
thingiverse
This is a spool made for 100ft of paracord, although it can be used for other things You need to print two spool halves, (25% or more infill recommended) and the spool connector, ( 100% infill recommended). the connector may be loose or too tight...
thingiverse
A simple spool to hold 100ft of your typical 1/4" / 6mm paracord. I wanted a way to store it up on some pegboard or a branch and keep it from unraveling all over the place while not in use. There are three holes and a notch that help do that. See...
thingiverse
... their thread, then you can screw the whole thing together. Ready! The slot in the outer part is for squeezing in the other end. Tip: If you take a cordless screwdriver and hold the other side with a pen you can super easily roll up the paracord
thingiverse
The paracord locks when you feed it past the locking jaws and into one of the holes. It is designed to fit on a 200mm square bed with enough space to run a skirt to start up the filament flow. It is also a good way to use up left over lengths...
thingiverse
Great way to carry your Paracord. Wind it on like a kite string and stool off as much as you need. The built in cutter makes it easy to cut the length you need. To keep it small, I didn't add a lighter to seal the ends but a lighter lives in your...
thingiverse
Holds 550 paracord. There are a bunch of these out there, but I found the other designs lacking. This holds 100 ft of cord. This uses normal rectangular razor blades (aka scraper blades, Stanley 11-515). This is .2" thick and doesn't flex. ...