passthrough 3d models

Edit: 2022-03-28: Created a v2 that's a bit thicker and has an additional passthrough for a GX16 connector. It turns out this last connector is actually in the way of the PCIe horizontal bar, and should be raised about 10-15mm or so before printing,...

This Gecko rear will replace the standoffs completely. Was printed on SLA machine, so not sure on how well it would print on FDM. Experiment, and report. Recommended to have 2x 3mm screws go completely through the bolt holes (May need a bit of...

I designed a climate-controlled case for my printer, but required an efficient method to feed the filament into the box. This component accommodates two of these adapters which pair perfectly with that coupling mechanism.\r\n\r\nMy enclosure is...

<p>Print in TPU&nbsp;</p><p>The splitter I used:</p><p><a...

Simple and slick case for generic 2 Relay Modules like in the picture. Both parts click together and hold the board firmly. No screws needed. Feel free to make Remixes to fit other kind of those little boards :D Disclaimer: Not tested for...

Threaded two part filament guide designed to pass through the top of an IKEA Lack table.Simply use a 1 inch hole saw to drill the hole for it to pass through, I had to shave the hole in the table a little bit with an exacto to make it fit since...

This is a battery door that fits GoPro Hero 9 through 12. Designed so that you can plug in a USB cable while the door is closed. ...I have personally tested with Hero 10 and others have posted makes showing it is working with Hero 9-12. Make sure to...

<p>The original <a href="https://www.prusaprinters.org/prints/58873-angled-heatbed-cable-cover-remix">Angled heatbed cable cover REMIX by Antonin Pa</a><a href="https://www.prusaprinters.org/social/36061-antonin-pas">š</a> didn't have enough room...

front stinger bumper for scx6 honcho with winch cable pass through has 2 different mounting holes for a different look i used the all the way hole to keep it fully flush opens the front wheels way better then the stock bumper fits perfectly

This part is specifically designed for Stepcraft D840 machines, but it should also fit every other machine in the D series without any issues. After experiencing two frustrating cable tube jams that ripped cables out of the controller, I decided it...

This is a filament pass-through for a printer enclosure that was custom-designed for an Ikea TINGBY coffee table-based enclosure. As it stands, this design is quite niche, with only a few potential users out there, so any feedback or suggestions...

<p>Remix of the great PC4-M10 version of this thing for use the <a href="https://e3d-online.com/products/embedded-bowden-collet-for-metal-1-75mm">E3D Collet</a> and <a href="https://e3d-online.com/products/collet-clips-pack-of-2">E3D Clip</a>.</p>...

The original was too tight, so I resized it to perfectly fit a bowden tube for 1.75mm filament. ...The hole is slightly larger than 4mm.

<p>This is a filament pass through for a printer enclosure. It was designed for my enclosure which is based on an Ikea TINGBY coffee tables. I'm pretty sure there are few if any folks out there using the same, so this is a very niche design right...

This is a remix of the original design https://www.thingiverse.com/thing:4746245) Changes: * Slightly moved opening for SYNC button * Removed top of opening for bluetooth module for easier printing

Designed to fit 3030 3N profile allowing a cable to wrap around the end of the profile without risk of damage on any sharp edges on the end of the profile. The fit is tight enough that they just need a few knocks to insert and then do not fall out. ...

Have you wanted a sweet looking filament guide/pass through for your IKEA Lack enclosure, but came up short after hours of searching on Thingiverse? This filament guide was designed for you. Based on the original dragon design and ornament remix by...

This is a grommet insert giving you a bulkhead that will accept two 8-pin ATX power connectors. Either EPS/CPU or PCIe are compatible. This secures the cable and gives it a very clean look. The design allows you to run extensions from your...

Threaded two part filament guide designed to pass through the top of an IKEA Lack table. Simply use a 1 inch hole saw to drill the hole for it to pass through, I had to shave the hole in the table a little bit with an exacto to make it fit since...

Remix of the great PC4-M10 version of this thing for use the [E3D Collet](https://e3d-online.com/products/embedded-bowden-collet-for-metal-1-75mm) and [E3D Clip](https://e3d-online.com/products/collet-clips-pack-of-2). YMMV so the STEP file is...

Simple and slick case for generic 2 Relay Modules like in the picture. Both parts click together and hold the board firmly. No screws needed. Feel free to make Remixes to fit other kind of those little boards :D Disclaimer: Not tested for safety of...

Threaded two part filament guide designed to pass through the top of an IKEA Lack table. Simply use a 1 inch hole saw to drill the hole for it to pass through, I had to shave the hole in the table a little bit with an exacto to make it fit since...

Couldn't find any free to use wall pass throughs that I liked, so i designed my own. Made for 12mm drywall walls. It's adjustable and will fit anything 80mm+. Print with 50%+ infill, **threads upwards**. Drill a 35mm hole straight through the...

I was close to coming up with something very similar, but the original creator nailed it first. Despite appreciating the original and not seeing any major issues, I think adding fillets in strategic locations can provide extra support. This remix...

little shelf with wire pass through hole i made for HTC base station to fit in a corner

Remix to fit heatsink and mount to my custom Ender external Electronics case: https://www.thingiverse.com/thing:5359962

Wall mount for the 2A Bosch e-bike battery charger 36-2. The battery cable can be hidden behind the charger housing, there is a canal to hold it. The Bosch fits nicely into the holder and doesn´t clatter around too much, Maybe you can even scale to...