pc fan mount 3d models
441805 3d models found related to pc fan mount.grabcad
This mount allows you to add an additional fan to a PC when normal mounting options are not available.
thingiverse
An 80mm PC fan mount for the E3D V6 Extruder, to mount to the Valleman K8200. This mod is a lot quieter than using the standard fan. IDEA... ... You may even use the pulse out on a PC fan to make your own speed controll for the fan.
thingiverse
This is a simple clean print to turn a 120mm pc fan into an exhaust fan. It's sized for 1/2 inch dry wall but could be extended further if need be. The 2 parts press fit together so you need to ensure you tolerances are pretty good or you may have a...
thingiverse
This is a fan mount for a 120mm fan and has room in the base for a boost converter.
thingiverse
... the BeQuiet! ...SilentBase 800 PC case. With this mount it is possible to mount a 120 mm fan at the side panal of the SilentBase 800 if you are using one or two GTC 980 Ti graphic cards (or a other card wiht this form factor). ...How I Designed This
thingiverse
Fan Mount for a 120mm Fan in the front Bay instead of CD/DVD Drive
thingiverse
PC Monitor fan holder I spend a lot of time at my PC and in the summer its gets kinda warm, I found commercial fans designed to keep you cool tend to be too forceful and too noisy and get irritating blowing in your face, so I thought I would put some...
thingiverse
... for radiator screws. I used M3 standoffs to offset the SSD from the fan bracket. Take care to make sure your SSD mounting screws don't interfere with the fan blades. ...If they do, let me know, and I can make a version with countersunk screw holes.
thingiverse
http://www.thingiverse.com/apps/customizer/run?thing_id=263573 Instructions Using the following options: Pin_height = 6 Rods_and_rings_wide = 1 Ring_or_segment = 1 Thickness_of_the_plate = 1.75 Head_diameter_mounting_screw = 6.5 Drop_or_ring = 0...
thingiverse
This version is for the 14cm PC fan model shown in the photo and a 17mm diameter ball on the suction cup phone mount The rigidity of the ball joint is **adjustable** via the screw The adapter also **screws** onto the 14cm fan with the two, original...
thingiverse
You will need this fan mount if you are using one or two GTX 980 Ti graphic cards (or one or two with a similar form factor) and a huge CPU cooler. It is printed in ABS in three parts. No support is needed. I have glued the two huge parts with "UHU...
thingiverse
A PC Fan Mount for personal camping fans, solder filtering, and other multiple uses. ...This is a revised version of the earlier version I created a year ago.
thingiverse
PC Fan mount (single and Double) Designed for any external use. Can be activated with a lipo battery (11.1v)Make sure to check what your PC fan is rated for! Can be used as personal fan, can have cabon filter added to it for soldering fumes, can have...
thingiverse
What is needed:- 12cm PC fan from old PC power supply. Keep the 4 screws for mounting later. Clips x2: straighten clip and used as hinge. Double size tape: stick mount on LCD side. ...Buy a MicroUSB 5V to 12V DC-DC...
thingiverse
Holds fan at 35 degrees toward the wall I used this for my wall mounted camera server to keep the drives cool.
thingiverse
i`ve got an improved version with proper screw holes. ... Print Settings Printer Brand: MakerBot Printer: MakerBot...
thingiverse
The design is mountable with standard PC fan screws and will fit a 120mm fan slot using existing mounting holes. This is also designed to be positioned either vertically or horizontally based on the space allowed in your case. NOTE: This is...
thingiverse
Bonjour, Voici mon premier prototype de support pour un ventilateur DIY composé de 4 ventilateurs 80mm d'ordinateur fixe. Les parties ne sont pas complètes, je vais les ajouter d'ici peu quand j'aurais séparé les pièces imprimables. ...
thingiverse
Inspired by [devid89's aquarium fan mount](https://www.thingiverse.com/thing:467586), I designed a similar model that can be adapted to different sized fans and has an adjustable fan angle. This design accomodates common sizes of case fans (80, 92,...
thingiverse
Aquarium Fan Mount A bracket for mounting a computer case fan to a rimless aquarium without screws Remixed from @pootermobile aquarium fan mount, I designed a similar model that can be adapted to different sized fans. This design accomodates common...
thingiverse
I separated the Fan Mount Body from the Fan Mount Top to allow ease of assembly when installing the fan and mount inside the case. The Top Grill is separate so you can install a filter screen between the Grill and Mount. I used super glue to secure...
thingiverse
single bolt mounts to affix 120mm at 90deg on a 5mm glass panel, mine personally is for thermaltake core p3 open case, pictured printed on photon s in craftsman resin then sparingly sprayed matt black
thingiverse
Customized version of https://www.thingiverse.com/thing:2333947 Created with Customizer! ...https://www.thingiverse.com/apps/customizer/run?thing_id=2333947
thingiverse
Customized version of https://www.thingiverse.com/thing:2333947 Created with Customizer! ...https://www.thingiverse.com/apps/customizer/run?thing_id=2333947
thingiverse
the holes are for m3 bolts check out my T-nut if needed: https://www.thingiverse.com/thing:2469130
thingiverse
I need a Second Fan Holder for my PC Case. Print with Ultimaker 2+ Ex, Slicer was Cura: All normal Settings Normal:0,15mm Nozzle 0,4mm All other Settings: Standard. ...
thingiverse
Customized version of https://www.thingiverse.com/thing:2333947 Created with Customizer! ...https://www.thingiverse.com/apps/customizer/run?thing_id=2333947
thingiverse
Customized version of https://www.thingiverse.com/thing:2333947 Created with Customizer! ...https://www.thingiverse.com/apps/customizer/run?thing_id=2333947
thingiverse
Customized version of https://www.thingiverse.com/thing:2333947 Created with Customizer! ...https://www.thingiverse.com/apps/customizer/run?thing_id=2333947