perc h310 3d models
126 3d models found related to perc h310.prusaprinters
A fan bracket to mount a Noctua 40mm fan (or presumably any 40mmx10 fan) on your PERC H310 HBA. I included a little 0.5mm spacer that may help achieve the right friction fit. Alternatively, just scale the model up/down a bit in the Z dimension.
thingiverse
... might work with some minor adjustment. Printed using iglidur i190-PF, though any filament with a higher application temperature than PLA should work (ABS/PETG). Remixed from https://www.printables.com/model/309314-perc-h310-40mm-fan-bracket
thingiverse
This is a remix of sorts from this model; https://www.printables.com/model/309314-perc-h310-40mm-fan-bracket The heatsink is slightly shorter on the H200 so the top clip now goes over the top of the PCB instead of the heatsink like on the H310, I've...
thingiverse
Customized version of https://www.thingiverse.com/thing:16054 Created with Customizer! ...https://www.thingiverse.com/apps/customizer/run?thing_id=16054
thingiverse
This is a mount to mount a 40mm fan to a Dell H310 Perc HBA-card.
thingiverse
Downstem w/ built in diffusor/perc and 14mm female hole for bowls. 14mm opening splits into 4 separate paths to diffuse air bubbles. Outer diameter of downstem has 18mm taper to fit most glass. ...Made in tinkercad
prusaprinters
Dell PERC H200 HBA cards are often repurposed to home built NAS computers. Due to the nature of a home PC case, these cards receive quite a bit less air flow in comparison to their common use in enterprise rack servers and tend to run very...
thingiverse
Dell PERC H200 HBA cards are often repurposed to home built NAS computers. Due to the nature of a home PC case, these cards receive quite a bit less air flow in comparison to their common use in enterprise rack servers and tend to run very hot. ...
thingiverse
Customized version of https://www.thingiverse.com/thing:247231 Created with Customizer! ...https://www.thingiverse.com/apps/customizer/run?thing_id=247231
thingiverse
Print with outside support and 100 percent infill if you use cold water it keeps cool for up to two joints
thingiverse
Customized version of https://www.thingiverse.com/thing:3516901 Created with Customizer! ...https://www.thingiverse.com/apps/customizer/run?thing_id=3516901
thingiverse
Smooths out the burn of the pen and lets you enjoy the flavor even with the heat up high. ... print 100% infill 2mm pt fill to an inch or so for best results (updated for more water space ->more cooling)
thingiverse
Good day, today i bring a beaker bottom with a extended quad tree perc, the dimensions are 181mmx139mmx176mm. The design is 3d printable and I reccomend Slic3r/Cura/simplify 3d for the gcode because some other programs skip layers. Good Luck. For...
thingiverse
Customized version of https://www.thingiverse.com/thing:1039106 Created with Customizer! ...https://www.thingiverse.com/apps/customizer/run?thing_id=1039106
thingiverse
Customized version of https://www.thingiverse.com/thing:2224678 Created with Customizer! ...https://www.thingiverse.com/apps/customizer/run?thing_id=2224678
thingiverse
Customized version of https://www.thingiverse.com/thing:16054 Created with Customizer! ...https://www.thingiverse.com/apps/customizer/run?thing_id=16054
thingiverse
commentor said it stacks too much and water gets in so you need a perc downstem or honeycomb. Here you go! ... **Please note, this has not been tested yet**