phone holder for trampoline 3d models
2434832 3d models found related to phone holder for trampoline.thingiverse
... smartphone recordings of your trampoline tricks. ... NOTE: I am not responsible for damage done to your phone, trampoline,self, etc by using this part. I thought this was uploaded on 9/8/20. I'm not sure why it was removed. ...This is a re-post.
thingiverse
This prevents a robotic lawn mower to get stuck on the base of a trampoline. ... It's a holder that snaps onto trampoline legs of approx 38 mm in diameter. Will hold a wooden beam that is 28 mm wide. ...
thingiverse
Replacement For trampolines top net holder. ... Pipe size: 25mm
youmagine
for diameter 1" & 0.060" (25.4mm, 1.5mm) thick steel tube often used for poles on trampolines. I used 1.5mm2 cable through it but use any type of cord that will fit... Use many layers when printing to get a strong part. ...I used my own TPU filament...
pinshape
for diameter 1" & 0.060" (25.4mm, 1.5mm) thick steel tube often used for poles on trampolines. I used 1.5mm2 cable through it but use any type of cord that will fit... Use many layers when printing to get a strong part. I used my own TPU...
cults3d
for diameter 1" & 0.060" (25.4mm, 1.5mm) thick steel tube often used for poles on trampolines. I used 1.5mm2 cable through it but use any type of cord that will fit... Use many layers when printing to get a strong part. I used my own PI-ETPU 95-250...
thingiverse
for diameter 1" & 0.060" (25.4mm, 1.5mm) thick steel tube often used for poles on trampolines. I used 1.5mm2 cable through it but use any type of cord that will fit... Use many layers when printing to get a strong part. I used my own PI-ETPU 95-250...
thingiverse
Holder for the protection net for trampoline, for example hudora
cults3d
Trampoline net holder endcap - Trampoline net holder endcap - Trampoline net hat This is Version 3.0 The illustrative picture is of a previous version with no base.
thingiverse
This is a replacement part for the trampoline net holder. ...I printed this in PETG for better outdoor lifespan, but PLA should work fine as well.
thingiverse
This is a net holder for the safety net on an 8ft trampoline. ...The net is supported by a metal pole at the top
myminifactory
Safetynet holder for trampoline. The object is located below a tarpaulin, so it worked fine for me printing it just en PLA. 20% infill 3 outer layers. ...Printed on prusa mk2.
thingiverse
This is a replacement for a songmics trampolines mesh holder. The slot to enter the rod is tight fit but prevent the rod jumping out. I printed it flat laying on side to have the forces across the layers. ...
thingiverse
The safety net holders that came with the trampoline break after a while. ...So I made a replacement.
thingiverse
This is the net holder for a 14' trampoline sold by KMart in Australia and possibly elsewhere in the world. Best printed laying on it side as it has more strength. It tends to shear if printed standing upright. After a recent wind storm blew our...
thingiverse
this is my second edition of this trampoline wall holder, and it is pretty strong. ...printed on my Ender 3 pro
thingiverse
So I designed this mug holder which is easily attached using one or two zip-ties on the trampoline safety net poles. It works great and holds the water bottles, mugs and cans safely during jumping. Can of course be used as a mug holder on any...
myminifactory
Here the design of a tube end cap to hold the net for a trampoline Steel tube data: Outer diam 25.4mm / 1" Thickness: 1.5mm / 0.06". Needs to be printed in flexible material.
thingiverse
... of my trampoline weared off, and the new one we bought seemed to be smaller in height. ...Therefore, i couldn't attach it to the net holder, and needed custom ones so i can screw then lower on the tubes. ... This is my first creation, kinda basic.
thingiverse
This is a replacement part for a trampoline safety net. Diameter up to 26mm is suitable. All my project files, instructions, schematics, are provided for free so everyone can enjoy them. Feel free to support me, so I can create and share even more...
prusaprinters
The parts shown in the picture broke on my trampolineI modeled a replacement for everyone to use. Print settings don't matter almost at all, the part is made for 3d printing and should be printable with the vast majority of materials. ...I recommend the...
thingiverse
The web picture I included says models around 2010 and 2011, but my trampoline was purchased in 2016 and it fits all the same. Let me know how it works or if you run into any issues. Print Settings Printer Brand: PowerSpec ...
thingiverse
The factory net holders crumbled after 2 years; too much harsh SoCal light. These should last longer especially if you use a UV-block coating. ...There is a small ventilation hole that is angled upward to prevent water from entering.
thingiverse
Designed for replacing the plastic holder for the pole, of the the safety net form a trampoline print it in abs for strenght
thingiverse
Alternative net holder for Ultrasport trampolines that you can use instead of the cap, that comes with the trampoline. It is designed for tubes with an outer diameter of about 25.5 mm. ...I use it with an 8 mm elastic cord that is fixed with cable ties.
prusaprinters
Alternative net holder for Ultrasport trampolines that you can use instead of the cap, that comes with the trampoline. It is designed for tubes with an outer diameter of about 25.5 mm. ...I use it with an 8 mm elastic cord that is fixed with cable...