photon mono x 3d models

It is what it is

This little thing ensures your top plate stays firmly in place during printing, preventing the xy axis from wobbling uncontrollably. ... V1: Snug fit guaranteed V2: Tight seal every time V3: The ultimate choice - square handle bars for maximum...

This little thing prevents your top plate from rotating during printing around the y axis so that the xy axis are not stable. ... V1: fits very tight V2: fits tight V3: like V2 with square handle bars (best choice) V4: like V2 with rounded handle bars

<p>Hello there, this is a support to let you to drain your resin bottle in to the VAT.<br/> It could be used with plate installed or not, and also with different size of resin.<br/> I think is very useful and in different situations.</p> <h3> Print...

Hello there, this is a support to let you to drain your resin bottle in to the VAT. It could be used with plate installed or not, and also with different size of resin. I think is very useful and in different situations. ...

(In combination with my design: I've tested 5 dripping holders, this was the best option so far read how to use it best. https://www.thingiverse.com/thing:4765628) A simple but effective way to prevent those few drops from reaching just outside the...

<p>Don't you just hate it when during manipulation of the build plate a resin drop lands on the outer edge of the vat, finding its way between FEP and glass ?</p><p>This design adds a large rim around the front of the vat.</p><p>Two versions are...

this is tight, you will need a hair dryer to heat up the plastic (pla) then slide it on all the way back, it was also designed to fit snug with the build plate so it doesn't shift when screwing it down after each print.

Remix of https://www.thingiverse.com/thing:4640934 MonoX build plate model by mrfumetsu. Adjusted the size of the build plate to 202x128mm. In the original model the build plate was 220mm wide (typo when designing?). ... The other parts -...

Vat cover for Anycubic MonoX 6k There are 4 file Cover Vat 6k is a complete cover for big printer (more or less 300mm) NO support needed The other 3 are the same cover but splitted for small printer (support needed) Attention: If you print the 3...

this is a remix of another design rotated 180 degree and made to sit on the right side. angled to drip into resin vat. ... resized for a easier fit.

Remix of https://www.thingiverse.com/thing:4640934 MonoX build plate model by mrfumetsu. Adjusted the size of the build plate to 202x128mm. In the original model the build plate was 220mm wide (typo when designing?). ... The other parts -...

Customized version of https://www.thingiverse.com/thing:4974330 Created with Customizer! ...https://www.thingiverse.com/apps/customizer/run?thing_id=4974330

Vat cover for Anycubic MonoX 6k There are 4 file Cover Vat 6k is a complete cover for big printer (more or less 300mm) NO support needed The other 3 are the same cover but splitted for small printer (support needed) Attention: If you print the...

<p>Just a quick file to clean out your vat without having to dump all of the resin out. This is good for small failures where you might have something stuck to your FEP.</p> <p>Instructions:</p> <ol> <li>Remove the bed plate.</li> <li>Take an old...

Just a quick file to clean out your vat without having to dump all of the resin out. This is good for small failures where you might have something stuck to your FEP. Instructions: 1. Remove the bed plate. 2. Take an old support piece with a flat...

This remix include: -prolonging the hanger to better support printing bed - it should stop rotating around the screw - it was 2 mm short in my printer -adding cut off so the screw lay flat on bed (earlier it was partially on hanger partially on...

Customized version of https://www.thingiverse.com/thing:4974330 Created with Customizer! ...https://www.thingiverse.com/apps/customizer/run?thing_id=4974330

Customized version of https://www.thingiverse.com/thing:4974330 Created with Customizer! ...https://www.thingiverse.com/apps/customizer/run?thing_id=4974330

Just a quick file to clean out your vat without having to dump all of the resin out. This is good for small failures where you might have something stuck to your FEP. Instructions: 1. Remove the bed plate. 2. Take an old support piece with a...

(In combination with my design: I've tested 5 dripping holders, this was the best option so far read how to use it best. https://www.thingiverse.com/thing:4765628) A simple but effective way to prevent those few drops from reaching just outside...

Fala Union Mono mount integration empowers both this superior design and its humble ancestor - the original Wade mount - simultaneously. ... You can discover Nicola P's original game-changing x carriage base for the esteemed Prusa i3 R2 by visiting...

2.8mm Z-Axis spacer for the Anycubic Mono X 6Ks to work with the Wham Bam Flexible Build System for Resin (FBSR). Just unscrew the two machine head screws under the Z-axis sensor paddle. Insert your printed piece (in resin or with FDM) then replace...

... ready to print with a Photon Mono X. The pre-sliced Photon Mono X file is checked with UVTools, so is ready to print, For the stl file I suggest to use UVTools after sliceing to remove some small islands and fix some problems due slicing software.

I designed this fume extraction system for my Anycubic Mono X and the Wash&Cure 2.0 station because I don‘t like the smell of the resin. I used two radial 75mm fans. The noise is about 52db. ... Titan fans (2x): https://amzn.to/3tKoujT Switch:...

When swapping out your FEP film on the ANYcubic Photon, place a simple disc of the right height underneath the FEP sheet as per Anycubic's guidance found in this YouTube video: https://www.youtube.com/watch?v=DLi3chV43LQ

Customized version of https://www.thingiverse.com/thing:4974330 Created with Customizer! ...https://www.thingiverse.com/apps/customizer/run?thing_id=4974330

This part can be screwed on top of the buildplate using the already existing threads. ...It is meant as a guide to drill evenly distributed holes for magnets as a replacement for the flexplate magnetic sheet

The human mind is a vast and mysterious universe, full of unexplored territories and untapped potential. It is capable of experiencing a wide range of emotions, from the depths of despair to the heights of euphoria. ...The human heart beats with a...