pigtail sma 3d models
4517 3d models found related to pigtail sma.thingiverse
... allows the connector to be fastened tightly to the mount without worrying about the connector rotating. This mount works for both SMA & RP-SMA female connectors. ... This mount was printed in Nylon with 35% infill and 200 microns of resolution.
thingiverse
This is a pigtail holder for the TBS Source one V5. It needs to be printed in TPU for its flexibility. ...It is designed so you can run the battery lead out the back.
thingiverse
Recommended for Lollipop or stubby antenna with pigtail SMA connector(Check other kitCopter designs for direct UFL pigtail connector). 2x 20mm standoffs needed. Height available for FC stack 28 mm. Micro FPV cameras 19 mm width. ...Adjust from 0 to...
thingiverse
Recommended for Lollipop or stubby antenna with pigtail SMA connector(Check other kitCopter designs for direct UFL pigtail connector). 2x 20mm standoffs needed. Height available for FC stack 28 mm. Micro FPV cameras 19 mm width. ...Adjust from 0 to...
thingiverse
Just a mix from flight ix5 lowrider frame antenna mount with antenna tube holes by Cliffstjohn Mar 25, 2018 https://www.thingiverse.com/thing:2839050 20 - 50%infill Happy flying! ...
thingiverse
MMCX antenna died. ...Had some SMA pigtails laying around and needed a holder for the GEPRC Mark5.
thingiverse
This thing can mount an SMA-Pigtail on the Back of your Quad. ... It was made for the Flywoo Mr.Croc but will fit many more Quads.
thingiverse
Small aero fin for mounting an SMA pigtail antenna to the Atto Sniper frame. ... Use a 2.5mm cable tie to secure it to through the slots in the top plate.
thingiverse
... TIP: to easily slide the pigtail inside without removing it from your vTX, you can slice the print at the location shown on the second picture with some snips, then slide the wire part of your pigtail in, so you can put the screws from the back.
prusaprinters
Also easier to print and without supports! I printed with the "face" having the screw holes on the bed, and the holes for the standoffs hanging at 45 degrees, just like the file preview on the viewer. TIP: to easily slide the pigtail inside without...
thingiverse
SabotageRC Dingo SMA pigtail / XT60 mount Print with TPU, no supports needed
thingiverse
A new version of the previous antenna mount, compatible with the TBS Unify SMA Pigtail with Screws.
prusaprinters
SabotageRC Dingo SMA pigtail / XT60 mount Print with TPU, no supports needed Category: R/C Vehicles
thingiverse
This is a TBS Unify VTX SMA pigtail holder for Dolphin1 frame. ...Fits pretty well on the rear standoff.
thingiverse
A turtle fin for the Atto Photon designed to give a surface mount SMA point for AXii and similar stubby antennas. ... Use a unify/FuriousFPV style SMA pigtail which will clamp securely into the inner holes in the fin.
thingiverse
SMA pigtail antenna mount for the Atto Photon frame. Fits straight SMA connectors with a fitment for the tabs found on the TBS and FuriousFPV version. ...Includes a small fin to protect the antenna and slots into the top plate, securing with 2 bolts.
thingiverse
I was having problems getting my X2Air double crosshair antenna to stay put with the smi rigid coax pigtail I used for the xair, so I came up with this little mount for a 90 degree SMA pigtail. It's angled at 30 degrees from the goggle level. ...
thingiverse
This is used to mount your SMA pigtail on a flexible base. It can be used for the type that is secured with two screws as well as the one that is only secured by a nut. ...Print it from TPU to get it flexible and durable.
thingiverse
I decided to remix the bottom half of the Nano Long Range to hold a TBS UNIFY PRO 5G8 RP-SMA PIGTAIL. With this mod, you can attach a Pagoda/Stubby style antenna for omnidirectional gain. I printed this with eSUN PLA+3D and I must say that I am...
thingiverse
## There are two variants: #### Variant 1 Here you have threads for M2 screw to fixate the pigtail holder. #### Variant 2 In this variant you have to use M2 screws and M2 nuts to fixate the pigtail holder. ## Every variant comes in three...
cults3d
There are two variants: Variant 1 Here you have threads for M2 screw to fixate the pigtail holder. Variant 2 In this variant you have to use M2 screws and M2 nuts to fixate the pigtail holder. Every variant comes in three flavors: doublethread ...
thingiverse
This is a Pigtail for SMA Antenna Mount (TBS version) specially design for the XBEE 230 V2. ... If you think there's something to improve, please tell me ;) If you want to know more about me, you can visit my YT channel :...
thingiverse
Customized version of https://www.thingiverse.com/thing:4089728 Created with Customizer! ...https://www.thingiverse.com/apps/customizer/run?thing_id=4089728
thingiverse
Inlay mount for TBS SMA pigtail. Insert pigtail into the slot. ...Glue it and melt the edges around the slot to keep sma plug in place.
thingiverse
TBS SMA Pigtail and R9 Antenna Mount for Martian 2 Frame Printed in TPU
thingiverse
Holder for the mmcx to sma pigtail for the Geprc Mark 4. ...It has two screw holes for m2 (or m3) nylon bolts to attach the pigtail.